When you’re framing a wall or adding trim molding, there’s a VEVOR pneumatic nail gun in the right size for your project. We have pneumatic nail guns for framing, concrete, siding, roofing, and finish work. Our 21-degree frame nailers fire 2- to 3-1/2-inch nails at 80-120 PSI. In contrast, our 14-gauge concrete nailers and 15-degree coil siding nailers tackle masonry and continuous siding runs. The full line of pneumatic nail guns features tool-less depth adjustment and sturdy aluminum housings for daily job site use. See the full selection below to find the framing, finish, brad, or roofing nailer right for your next job.
Are you nailing siding to a fence, building a wall, or fixing trim in a finished room? VEVOR air nail guns include framing nailers, concrete T-nail guns, coil siding nailers, roofing nailers, and staple guns. Each is designed for a specific nail gauge and collation angle. Each model connects to a standard air compressor and features multiple trigger settings. This gives contractors and DIYers consistent, jam-resistant nailing throughout a full day on the job.
VEVOR’s pneumatic nail guns come in categories by nail gauge, collation angle, and material, and choosing the right one saves time and reduces wasted fasteners.
These VEVOR pneumatic framing nailers use a 21-degree collation angle and fire full round-head nails 2 to 3-1/2 inches long at 80 to 120 PSI. This is the best big nail gun for structural work such as wall framing, subflooring, and deck building, where longer nails need to penetrate deep into dimensional lumber.
Two trigger modes let you choose between sequential firing for precise single-shot placement and contact firing for rapid-fire production work, without changing any tool parts. A high-strength aluminum magazine with 60-nail capacity reduces reload stops during a framing run, and an open-nose design speeds up jam removal when it does occur.
The tool-less depth adjustment lets you easily adjust for flush or countersunk nail placement by hand, which can help when you switch between softwood framing and denser engineered lumber on the same job. VEVOR also has a 15-degree coil framing nailer for coil-fed framing work, another member of the pneumatic framing nailer family. This nailer accepts 1-3/4 to 3-1/2-inch nails and a 225-nail side-loading magazine, giving crews a higher-capacity option for large-scale construction and renovation projects.
Direct fastening to concrete or masonry requires a different tool altogether. Among VEVOR pneumatic nail guns, the concrete nailer is the one for the job, working with 14-gauge T-shaped nails ranging from 1 inch to 2-1/2 inches long. This T-nail gun is powered by 0.4 to 0.8 MPa air pressure.
It can drive fasteners into concrete, brick, and other hard surfaces with enough force to avoid bent nails or shallow penetration, which are common problems when contractors try to use a regular framing nailer on masonry. For repetitive fastening jobs, such as attaching furring strips or connecting plates to a slab, a sliding-load magazine that holds 50 to 100 nails keeps the concrete nailer running without constant reloading.
The aluminum housing weighs just 6.6 pounds, so it’s light enough for overhead or extended use and rust-resistant in damp construction-site conditions. The design includes an ergonomic rubber grip and a safety lock switch to prevent accidental firing; both help reduce hand fatigue, which is vital for tools rated for masonry-grade fastening force.
A coil-fed magazine is a better choice than a stick magazine for siding installation because coil siding nailers carry far more fasteners per load than stick nailers, keeping teams moving across long wall lengths. VEVOR’s 15-degree coil siding nailers offer several nail lengths depending on the model – from 1 inch to 2-1/4 inches on the compact variants up to 2 to 3-1/4 inches on the bigger siding and frame combo rivet nut gun kit, all running on 70 to 120 PSI of air pressure.
The tool-less depth adjustment allows installers to fine-tune nail depth, and the 360-degree adjustable air exhaust lets installers direct exhaust air away from their face – a minor but essential comfort feature for long siding tasks. Some coil siding nailers feature large-capacity magazines that store up to 300 nails at a time, and a bump-fire setting helps experienced users keep up a quick nailing pace on fencing, decking, pallet, and sheathing projects without releasing the trigger between shots.
The roofing nailer is a welcome addition to VEVOR’s line of pneumatic nail guns, a range that includes coil nails from 3/4 inch to 1-3/4 inch at a 15-degree angle, with two firing modes for you to choose from, specifically developed for shingles and roof decking where a wide surface demands speed and uniform depth.
Finish nailers use 15- or 16-gauge nails, while brad nailers use thinner 18-gauge brads. Both are generally used for lighter trim, molding, and cabinetry work when the bigger fasteners of a framing nailer would damage fragile material. Pin nailers go a step further, driving headless 23-gauge pins for the most delicate trim and veneer work where even the smallest nail head would be visible.
These finishing tools use thinner-gauge fasteners than framing or concrete nailers, but operate on the same pneumatic principles: an air compressor provides the driving force, and a trigger valve releases it precisely when needed. If you’re building a whole workshop, a heavy-duty framing nailer combined with a finish or brad nailer covers structural and finish-carpentry duties without a hole in capacity.
Other factors such as nailer type, nail gauge and collation angle compatibility with your fastener supply, and knowing how to use the trigger and depth controls will dictate how well a tool in VEVOR's pneumatic nail guns portfolio works from day to day.
Nail gauge and collation angle aren't interchangeable between VEVOR’s pneumatic nail guns, so checking compatibility before buying fasteners in bulk saves wasted trips back to the store. Most frame nailers fire 21-degree full round head nails that are 2 to 3-1/2 inches long. Coil framing and siding versions employ a 15-degree collation angle instead, which alters the nail strip form and magazine design.
Concrete nailers use their own 14-gauge T-nail format, which isn't compatible with any frame type. Magazine capacity is all over the place, like VEVOR’s pneumatic nailers, from a 60-nail stick magazine on the regular framing nailer to a 300-nail coil magazine on some siding models, with the 14-gauge concrete nailer’s 50- to 100-nail slide magazine in between.
Staple guns in the same pneumatic family load fine-wire or medium-crown staples instead of nails. Gauges range from 13 to 22 depending on whether the work is upholstery, roof decking, or carton closing. The fastest method to avoid a jammed or mismatched tool in the middle of a project is to match gauge, angle, and capacity to the actual fastener box you have, especially if you’re switching between many pneumatic nail guns on the same job site.
The majority of VEVOR’s pneumatic nail guns provide two trigger modes: Sequential firing, which requires you to pull the trigger for each nail, and contact firing, which allows for continuous firing as long as the trigger is held down and the nose is touching the work surface. Sequential mode is for accurate placement of one nail at a time.
Contact or bump-fire mode is for repetitive jobs like sheathing or fencing, where the placement tolerance is more relaxed. Tool-less depth adjustment is expected across the series, letting users spin a dial by hand to place nails flush or countersunk without reaching for a separate tool.
You’ll see high-strength aluminum housings on framing, concrete, and siding nailers, balancing weight and durability for equipment that gets dropped, bumped, and used all day on active job sites. Some versions include a safety lock switch to prevent accidental discharges, a vital safety feature on any pneumatic nail gun with enough force to drive a nail through masonry or hardwood framing board.
VEVOR offers a selection of pneumatic nail guns, including 21-degree framing nailers, 14-gauge concrete T-nail guns, coil siding nailers, roofing nailers, and staple guns, all with tool-less depth adjustment and dual-trigger modes. Each nail gun lets contractors and DIYers achieve professional-grade fastening without the professional-grade price tag. With rapid shipping, easy returns, and solid after-sales support with every order, there’s little reason to pay more elsewhere for the same aluminum-housed durability. Check out the entire range of VEVOR pneumatic nail guns online and discover the nailer ideal for your next project.
Most framing and siding nailers run between 70 and 120 PSI, whereas concrete nailers operate at 0.4 to 0.8 MPa. Check your model's rating and select a compatible air compressor.
No. Coil nailers use a round wire collated strip, while stick nailers load flat strips of nails. The collation and magazine systems aren't interchangeable across tool designs.
Pneumatic nail guns often provide more consistent power and lower cost per nail, but they require an air compressor and hose. Cordless models sacrifice some power for greater job-site mobility.
A conventional stick-fed framing nailer carries up to 60 nails per load. Coil-fed variants used for framing and siding carry substantially more, with some magazines rated for up to 300 nails.
