Does your VEVOR slushie machine start producing strange noises and not making the same fluffy frozen as before, and it turns out to be a nightmare? Then it’s time to clean it. But do you know how to maintain and clean your slush machine? Bacterial growth can affect the taste and quality of your drink if it is not maintained and cleaned properly.
But there’s no need to worry, as cleaning a slushie machine is doable and will be humming again in no time. Following a few steps, you can refresh your slush machine and allow it to work like a new one.
Let’s dig into this article and learn how to clean your slushie machine by following a few easy steps.
Signs that your VEVOR Slush Machine Needs Cleaning
Every machine needs cleanliness and maintenance, so consider the cleaning process when you see mold growing on the machine. The build-up of mold can cause cancer and indigestion problems. However, if your slush machine is used regularly, don’t skip the cleaning process.
A few signs are listed below that would help you understand your slush machine needs a cleaning:
1. Build Up Mould
2. Leaking Tray
3. Noise coming from the Machine
4. The machine stopped spinning.
5. The machine stops making slush
Preparation Before Cleaning VEVOR Slush Machine
Ensure the switch is off before cleaning, as the machine is not in a good state. Based on local safety standards, you must wear cleaning supplies for every cleaning and maintenance job.
● Wear gloves against any accident.
● Avoid solvents and flammable substances.
● Avoid using tough and metal sponges.
● Don’t use a bowl to wash the parts.
● Avoid spraying in nearby areas.
● Don’t use the water directly to the machine.
● Parts of the machine shouldn’t be dry on the furnace or oven.
● Use warm water, and cleaner can be used.
After finishing the cleaning and maintenance job, put your gloves and guards in a safe space to secure them properly. To ensure such quality and maintenance meet local standards.
Step-by-Step Guide to Clean VEVOR Slush Machine
Follow these step-by-step guides to clean the VEVOR slush machine:
1-Empty Bowl
Empty the bowl before starting the cleaning process. Don’t empty the bowl if you’re using it the first time. Set the bowl setting button to “clean state” before operating.
2-Disassembling the Machine
It’s recommended to disassemble the tap before removing the bowl. You can’t disassemble the tap before it’s positioned carefully. With a screwdriver, remove the fastener, and then the dispensing handle should be moved upward.
After this, you need to push the piston, spring downward, and remove the O-ring.
Now, put all the slush machine parts in the warm water; the water temperature should be 50. Remember to not dissemble the parts when you notice liquid in them.
3-Moving of Bowl and Cover
To clean the VEVOR slush machine, you need to move out all the bowls and clean the machine.
Lift and take out the upward cover. To remove the tank completely from its seat, you need to pull the tank upward and outward to remove it from its seat. Now screw off the nuts and take out the stirrer and seal.
4- Disinfecting and Cleaning
It’s time to clean all the dismantled parts according to the local hygiene standards. To do this, follow the instructions:
● Pour water into the container and add 2% of sodium hypochlorite to the water.
● Clean the bowl and evaporator and cover thoroughly with the water by using a sponge.
● Now, put the sanitizer in another basket and put all the disassembled parts in it for 30 minutes to sanitize.
● After 30 minutes, thoroughly clean the parts with water and let them dry. Clean the roof and other parts with sponge water.
● After retaining for 30 minutes, clean the bottom surface with water twice by using a sponge.
● At the dry area, put on the cover and dry it with a rag.
● Before taking away the cover, clean it with water.
5-Resetting of Cleaning Parts
All the cleaning parts are now time to reassemble, but some parts need lubrication to work normally.
Replace the gasket at least after a year but need to look at it regularly.
Use the provided vaseline and lubricate the seal.
If you see motor parts are leaking, replace the seal ring. Connect the motor with the motor bracket and replace the head seal ring. Add some Vaseline, and then install the motor bracket.
Now, fix the stirrer and install the cover in the appropriate location.
The top roof should be pressed down until the joint fits with the motor base. Apply the Vaseline to the bolt overall and insert screws once the taps are steady.
6-Clean Steps Before Using The Slush Machine
Below cleaning steps are required before using the VEVOR slush machine:
● Fill a bowl with water
● In cleaning mode, start the machine and stir for 5 minutes
● Open tap to clear the machine after stopping the machine
7-Drip Tray Cleaning
For drip tray cleaning, you need to follow the instructions carefully. You must empty the drip tray and clean it every day after using the VEVOR slush machine.
Using warm water, clean the drip tray and grid completely after emptying it. By lifting the drip tray from the top, take out the drip tray.
Clean the machine with a wet rag and dry the parts.
8-Bulb Replacement
You can only change the bulb when the machine is off. To replace the LED bulb, open the small black panel and close it.
9-Slush Machine Condenser Cleaning
Professionals should clean condensers as they abide by local laws and regulations. However, a dirty condenser can affect the machine’s efficiency. Even if the front and back plate is not installed, the machine is banned from use.
One bowl Slush Machine Condenser Cleaning
Take out the side panel after losing the screws. Brush the dust from the condenser surface parts.
Two- Bowl Slush Machine Condenser Cleaning
Loose the three screws from the back plate and 5 from the side plate to clean the two-bowl slush machine. Then, take out the side panel.
After cleaning, dismantle security protection parts and use a dry bush for dust brushing from the condenser surface.
Tips for Maintaining Your VEVOR Slush Machine
To maintain the VEVOR slush machine, follow the below steps:
● At least every once a year, your machine needs maintenance, so deep cleaning to replace the parts you need to look for.
● Timely maintenance will keep your machine in a safe state.
● If any parts get broken, you must replace them with the original manufacturer.
● You’re banned from using the machine if its parts are broken.
● It’s hard for a user to maintain a machine on their own. So call a professional when you observe any fault.
FAQs about VEVOR Slush Machine Cleaning
1- How often should a slushy machine be cleaned?
Slush machines should be cleaned and scrubbed once a week, from their tops down to their nozzles. You should fill it with lukewarm water and detergent once a month and let it run for a few minutes before wiping it down.
2- What safety precautions should I take before cleaning the machine?
To ensure machine safety, when people clean and maintain, they should lock out or isolate the energy sources. You will need to disable the energy sources and then lock them out to keep them from re-energizing.
3- Is it necessary to disassemble the machine for cleaning?
It is important to disassemble production equipment as necessary to allow for easier cleaning and sanitation of all parts since liquids and crumbs can get into the cracks and crevices of the machine, and bacteria and pests can get into the machine as well.
4- How can I extend the lifespan of my VEVOR Slush Machine?
You can extend the lifespan of your VEVOR slush machine by doing regular maintenance and cleaning. If any part of your machine gets damaged, try to replace it with the original one. Seek professional help if you don’t understand what type of faults you’re having with the machines.
Bottom Line
Give your VEVOR slush machine a deep cleaning and scrub once a week to fight with gunk, funk and mold. Use good detergent and lukewarm water to fill up your VEVOR slush machine with this mixture for deep cleaning; run it for a few minutes before wiping it. It’s a great way to follow the pesky guidelines and procedures to clean it.
