VEVOR Baby Gate, 29.5″-48.4″ Extra Wide, 30″ High Manual

Unlock the full potential of your VEVOR Baby Gate with our comprehensive product manual download. Whether you’re setting up the 29.5″-48.4″ extra-wide, 30″ high gate for your stairs, doorways, or any other area in your house, this manual has you covered. Designed to ensure ease of use, our detailed guide walks you through each step of the installation process, whether you’re using the pressure mount kit or the wall mount kit.

The VEVOR Baby Gate manual is your go-to resource for troubleshooting, setup, and optimization. It includes clear, user-friendly instructions and illustrations to make the auto-close, easy step walk-through feature a breeze.

This manual is invaluable for ensuring the security of your child and pet, providing you with peace of mind. Downloading the manual is quick and straightforward, offering you immediate access to all the information you need to get the most out of your VEVOR Baby Gate.

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret our user manual.

The appearance of the product shall be subject to the product you received. Please forgive us for not informing you again if there are any technology or software updates on our product.

INSTRUCTIONS

Thank you very much for choosing this dog gate. Please read all of the instructions before using it. The information will help you achieve the best possible results.

Model and Parameters

Product & Parts

BABY GATE MAINTENANCE

• Clean by using a sponge with warm water or mild detergent.
• DO NOT use abrasive cleaners or bleach.
• Check the gate regularly to ensure all hardware and mounts are securely tightened.
• Do NOT use if any component is damaged or missing.

STEP 1. Measure the width of the doorways

Following the extension combination suggestions to install the gate.

STEP 2. Insert the 4 bolts into the 4 corners of the gate/extension.

STEP 3. Pre-assemble the gate, and locate four points for hole drilling. Hold the wall cup in position and mark the center with a pencil.

PLEASE NOTE: The gate should be resting on the floor. Do not allow a gap of more than 0.5cm between the gate and the floor.

STEP 4. Stick the pad when using a pressure-mounted installation. Remove two sides of the sticky pad, stick 4 pads to 4 wall cups. Then the wall covers the bolts.

TIP: If you do not have to worry about damaging the walls, skip this step.

STEP 5. Drill hole for the 4 marked positions, then put dry wall anchor (g), and use screw (f ) and the wall cup (d)

STEP 6. Tighten the top of the tension knobs by turning them clockwise at the same time

Note: Make sure the bottom of the gate frame remains completely flat on the floor.

Next, tighten the bottom of the tension knobs at the top at the sametimebyturningthem clockwise.

Pay attention to adjusting the left and right clearances to ensure that the left and right clearances are consistent.

STEP 7. Cut off the belt and test the gate:

1. Push the gate to check stability.
2. Open and close the walk-through gate.

Pull the button to the right, then lift the gate panel to open.

BABY GATE TROUBLESHOOTING

Warning

• To prevent serious injury or death, securely install the gate or enclosure and use it according to the manufacturer’s instructions.
• Never use with a child who can climb over or dislodge the gate or enclosure.
• This product will not necessarily prevent all accidents.
• Never leave children unattended.
• Use only with the locking mechanism securely engaged.
• Intended for use with children from 6 months through 24 months of age.
• Stop using the gate if any parts are missing or become damaged.
• Children may die or be seriously injured when gates are not securely installed.
• ALWAYS install and use gates as directed, using all required parts.
• Periodically check all fasteners to be sure they are tight and secure.
• Adult Assembly Required.
• The surfaces to which the gate is to be fixed must be suitable for the purpose and structurally sound.
• Indoor use only. It is not to be exposed to outdoor elements.
• Install this gate away from heaters and other sources of heat.
• STOP using it when a child can climb over or dislodge the gate.
• You MUST install [wall cups] to keep the gate in place. Without [wall cups], the child can push out and escape.
• NEVER use it to keep the child away from a pool.
• Thanks for purchasing the VEVOR product!

Made In China.