VEVOR Baby Gate, 29.5″-53″ Extra Wide, 30″ High Manual

Unlock a world of ease and efficiency with the VEVOR Baby Gate manual download. This comprehensive guide is designed to help you set up, troubleshoot, and optimize your 29.5″-53″ Extra Wide, 30″ High Dog Gate for Stairs, Doorways, and House. The manual provides step-by-step instructions for utilizing the Easy Step Walk Thru Auto Close Child Gate Pet Security Gate with Pressure Mount Kit and Wall Mount Kit.

Written in a professional, user-friendly tone, this guide ensures that even first-time users can install their baby gate without hassle.

Detailed illustrations and clear explanations make it simple to understand the functionality and features of your VEVOR Baby Gate, ensuring the safety and security of your child and pets. Whether a new parent or a pet owner, this manual will be your go-to resource for maintaining and optimizing the gate, offering valuable troubleshooting tips and detailed setup instructions.

Download the VEVOR Baby Gate manual now and experience unparalleled convenience and peace of mind.

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret our user manual.

The appearance of the product shall be subject to the product you received. Please forgive us for not informing you again if there are any technology or software updates on our product.

INSTRUCTIONS

Thank you very much for choosing this dog gate. Please read all of the instructions before using it. The information will help you achieve the best possible results.

Model and Parameters

Product & Parts

BABY GATE MAINTENANCE

• Clean by using a sponge with warm water or mild detergent.
• DO NOT use abrasive cleaners or bleach.
• Check the gate regularly to ensure all hardware and mounts are securely tightened.
• Do NOT use if any component is damaged or missing.

STEP 1. Measure the width of the doorways

Following the extension combination suggestions to install the gate.

STEP 2. Insert the 4 bolts into the 4 corners of the gate/extension.

STEP 3. Pre-assemble the gate, and locate four points for hole drilling. Hold the wall cup in position and mark the center with a pencil.

PLEASE NOTE: The gate should be resting on the floor. Do not allow a gap of more than 0.5cm between the gate and the floor.

STEP 4. Stick the pad when using a pressure-mounted installation. Remove two sides of the sticky pad, stick 4 pads to 4 wall cups. Then the wall covers the bolts.

TIP: If you do not have to worry about damaging the walls, skip this step.

STEP 5. Drill hole for the 4 marked positions, then put dry wall anchor (g), and use screw (f ) and the wall cup (d)

STEP 6. Tighten the top of the tension knobs by turning them clockwise at the same time

Note: Make sure the bottom of the gate frame remains completely flat on the floor.

Next, tighten the bottom of the tension knobs at the top at the sametimebyturningthem clockwise.

Pay attention to adjusting the left and right clearances to ensure that the left and right clearances are consistent.

STEP 7. Cut off the belt and test the gate:

1. Push the gate to check stability.
2. Open and close the walk-through gate.

Pull the button to the right, then lift the gate panel to open.

BABY GATE TROUBLESHOOTING

Warning

• To prevent serious injury or death, securely install the gate or enclosure and use it according to the manufacturer’s instructions.
• Never use with a child who can climb over or dislodge the gate or enclosure.
• This product will not necessarily prevent all accidents.
• Never leave children unattended.
• Use only with the locking mechanism securely engaged.
• Intended for use with children from 6 months through 24 months of age.
• Stop using the gate if any parts are missing or become damaged.
• Children may die or be seriously injured when gates are not securely installed.
• ALWAYS install and use gates as directed, using all required parts.
• Periodically check all fasteners to be sure they are tight and secure.
• Adult Assembly Required.
• The surfaces to which the gate is to be fixed must be suitable for the purpose and structurally sound.
• Indoor use only. It is not to be exposed to outdoor elements.
• Install this gate away from heaters and other sources of heat.
• STOP using it when a child can climb over or dislodge the gate.
• You MUST install [wall cups] to keep the gate in place. Without [wall cups], the child can push out and escape.
• NEVER use it to keep the child away from a pool.
• Thanks for purchasing the VEVOR product!

Made In China.

 

VEVOR Baby Gate, 29.5"-53" Extra Wide, 30" High Manual