VEVOR Paper Cutter 12Inch A4 Commercial Heavy Duty Paper Cutter 300 Sheets 45HRC Hardness Stack Cutter Metal Base Desktop Stack Cutter for Home Office (A4)

There was some damage in shipping, but seems to work ok. Would be nice to have instructions or user guide. Still trying to figure out everything it can do - but what I've managed so far seems pretty great! I'd get it again, for sure! 30milesfromGrace

I love This cutter . It’s perfect for cutting the magnetic rubber I use to make refrigerator magnets . It cuts perfect . The smaller version cutter I had , did not do the job. This is perfect for making a straight cut. . Perfect for my use .

Generally speaking the materials used in the paper cutter construction are good quality. It is solidly made and arrived well packed and in a timely manner. The blade appears to be high quality and very sharp. So it's ability to cut through a lift of paper is excellent. Unfortunately, two deficiencies dramatically lower the overall rating. The backstop has no firm anchor points except for the single bolt where is attaches to the side guide. As such it does not stay in a tight fixed position and requires adjustment after every cut. While annoying it is still workable (for the price). The bigger issue is with the clamp. It is completely inadequate to hold the paper firmly in place during the cut. And while having cranked down the pressure very hard did help, the clamp now is not functioning correctly and will not raise and lower without manual assistance.

I love This cutter . It’s perfect for cutting the magnetic rubber I use to make refrigerator magnets . It cuts perfect . The smaller version cutter I had , did not do the job. This is perfect for making a straight cut. . Perfect for my use .

I've only done a couple projects so far and it's going well. The grease issue seems reduced to a normal amount compared to other comments. Mine came with the guide bar uninstalled. So far the guide bar is my only complaint. I tightened the screws quite well, but during use the bar gets knocked out of alignment even though I wasn't slamming the paper into it. I'm hoping once I get an angled tool to hold the screws in place while tightening the nuts this problem will be solved, but I can't use a regular screw driver due to the lip on the part (no access to the screw with a normal vertically held tool). They provided three alen wrenches and a double sided wrench already so I'd pay another dollar for them to provide an angled phillips screwdriver also. Something to consider, the operating lever requires a fair bit of head room / vertical clearance. It will not operate on a counter which has cabinets above it at a standard height. I say, "needs practice" because if you're just eyeballing the cut rather than using a measurement, it's not super easy to tell exactly where the blade will come down. That being said, I didn't ruin my first product after only doing 2-3 practice cuts so I'm happy with the slight variance and that should diminish as I practice. First project was cutting 70 sheets of 110lbs cardstock and it was super easy. I had no difficulty cutting through the stack. Does small trims easily and cleanly as well. Second project was 100 sheets of standard printer paper (20lbs?). Took me less than 5min to get my 200 half sheets plus trim the other lengthwise border off because why not, I could now (3 cuts total).

I have a document scanner and a whole slew of TV Guides, magazines and some paperback books from the 1970's that I wanted to scan and convert to PDF so I could have them on my iPad when I travel. I used to go to Staples and pay them $3 to cut the binding off of each book. I saw this and figured it would actually be cheaper to do it myself and after reading the reviews figured that I would try it. Well, I'm extremely happy. I've already cut and scanned at least 35 books/magazines. The cuts are clean and the scans are coming out perfectly.It took me about 20 minutes to unpack it and put it together and it's a bit larger and heavier than I expected but that just confirms the solid construction and quality.

Hi, I received my cutter yesterday and I am so so happy with it. It can cut a lot of paper with very little pressure and is set up perfectly for safety. I highly recommend this cutter for any serious paper cutting. Even people with arthritis can easily cut paper with this cutter. It is heavy but will last for years and years!

My husband ordered this and LOVES it :)

This thing is AWESOME! It is also very - very heavy. I decided to convert my book collection into digital form. Mainly manuals. This has helped me tremendously. I would recommend it to anyone.

FANTASTIC paper cutter! I gave mine away to a friend and will DEFINITELY be buying another soon!