All
Account
Ben Fogg Ben Fogg
6 L
Works well
0
Sharkpuncher Sharkpuncher
6 L
works well so far
Did a test run with this as soon as i got it and it worked exactly as it should, I will come back and update after I've used it for awhile if anything goes wrong. put a grease and grime caked piece in there with a bit of alconox and the water turned brown and it came out basically new.I feel like some of the complaints on here are people who are either not familiar with ultrasonic cleaners, or have unnecessarily high expectations for something that is relatively inexpensive from Amazon (like the one wanting a removable basin, lol).A few tips based on my own experience with past units, and just things that I observed with this.I prefer to fill it up with hot water. I had one years ago that recommended it, and I've just always done it since. at the very least it takes a lot less time to heat up, and my thought is that it puts less wear on the heating element.Fill it all the way up to where its marked. I think a lot of people might be underfilling these, which is leading to premature failure because the ultrasonic generator is effectively "tuned" to vibrate a full bath, not a half bath.Use the basket. it's not just there for convenience. you don't want things resting directly on the bottom.The temperature dial is exactly that. it is not tied to the ultrasonic generator, it is not going to shut off until you shut it off. the heat *should* cut off with a click, and the red light on the front going out, when it hits the temperature, but it will continue to hold at that temperature until you shut it off. if it's not doing that, you have an issue with the thermostat.don't just leave it totally unattended. I'd think this would be common sense but some of these reviews.....after you drain it from the spout and it's had a chance to cool down, tip it sideways to get the last bit out. there's a reasonable amount that pools in the drainpipe and leaving it to sit in there is also unnecessary wear and tearbased on the way this feels (slightly flimsy) I would also recommend finding
0
Bear Bear
6 L 4
Nice
Exactly as advertised.
0
J&E J&E
6 L 4
Cleans well but loud
Cleans great . .but a tad noisy . .have to use it in the garage
0
Robert Franz Robert Franz
6 L 4
A great find for the price!
Four Stars, but would have give Five if not for the following minor quirks. The unit requires two electric plug ins: one for the ultrasonic unit and heater, and then a second for the rotating motor which turns the vinyl lps. There is no turn off for the rotating motor, you need to either unplug it from the electrical outlet of unplug a connector piece on the cord itself. The ultrasonic vibrations are controlled by a front knob entitled "Timer". Yes, it works the timer, but more importantly it works the ultrasonic waves. Better to have labeled as "Ultrasonic" or "Start" or "On". The vinyl spinner motor just rests on the back of the tank. It fits nicely, but if not properly centered, the vinyl lps get stuck and do not spin. Lastly, you need to be very careful not to scratch your vinyls when putting them on the spindle, as the spindle has a threaded end which is sharp enough to do harm to the vinyl. Okay, that being said, it is a wonderful device at a very favorable price. I have used it on over 100 albums over the last 2 months with amazing results. Like others recommend, I too advise using some a small amount of 99% Isopropyl Alcohol with a couple of drops of Triton X-100 One last point, the customer service was helpful with a minor problem I had with the spindle, sending a replacement to me in a prompt manner.
0
Non Stop Horizon Non Stop Horizon
22 L
Cleans well, and the electronic controls for time and temperature are easy to use.
This item cleans well, and is convenient to use. Two aspects a purchaser needs to consider are the large mesh basket (1/2" square), and the dimensions of the basket (5-1/4" square at the top, 4" square at the bottom, 3-1/4" deep). Small parts will fall through the mesh, and long parts won't fit in the basket.
0
Non Stop Horizon Non Stop Horizon
22 L
very efficiant
I use this to clean my print heads and 1/2 inch of water and 15minutes later .... like new no clogs.
0
Dennis Marvin Dennis Marvin
6 L 4
Works well. A little noisy
0
MD DV MD DV
22 L
Overall happy with it
A little slow to warm up but it does the job very well. Cleaned a few carbs with it and it worked pretty good
0
Kevin Smith Kevin Smith
22 L
Would buy it again
Works great I wish I got a bigger one the only issue I have is it takes a while to heat up but not a machine issue
0

855-385-1880 Monday to Friday, 08:00-17:00, GMT-7