6" Diamond Core Drill Concrete Drilling Machine With Stand & Drill Bits 2180w

6" Diamond Core Drill Concrete Drilling Machine With Stand & Drill Bits 2180w

Available: In Stock
Product SKU: Z1Z-160SZJ0000001V1
$219.99 USD
Our core drilling machine combines functionality and versatility in one device. It is ideal for lighter drilling work.

Installation:

First, install the screw connecting the stand and the pedestal. Before use the drill, you need to fix it.
1. Remove the two screws on the back of the stand;
2. Seperate the stand and the pedestal;
3. Rotate the pedesta 180° and install the screws.
4. Install completed

Fix the driller:

Here are two ways
1.Using expansion link
Choose a hollow tube according to the height of the place which need to be drilled. Put one end of the tube against the adjustable screw rod. And turn the rod reversely to fix the driller tightly, expansion bolts are not needed.
2.Using ecpansion bolt
Make a hole on the wall or the groud and install the bolt;
Expand the bolt;
Install the screw rod and the stand. Then tighten the nut.

Install drill bit

Before installing, you need to smear some grease on the drill end thread in order to discharge easily. After instlling, you need to run the driller at an idle state at first.
Attention: Before you install or remove the drill bot, you must be sure the drill is powered off. Before running, the drill must be connected with clean cold water.

Here are the ways to inject water:

1. Using tap water: Connecting the tap and the machine with the injecting hose.
2. Hanging a bucket over the drill
3. Using water pump
4.Drilling
Start the drill at an idle state. Then open the water tap. When there is water flowing from the drill, you can start drilling. At first, you need to drill slowly and increase strength gradually. After you drill deeper than 5mm, you can increase your push strength. If the drill's rotating speed decrease, than proves that the drill is overloaded. Then you need to decrease the push strength, avoiding the drill being stuck. If there is smoke coming out, you must pull out the drill right away and start to drill after a while, avoiding the engine being burn down.
5.Material being drilled
When drilling reinforced concrete, current increases and the drill will vibrate. Therefore, you need to decrease pushing strength but the decreasing amplitude should not be too big. Otherwise, the effiency will be affected and the drill bit will be worn more badly. When drilling reinforced concrete containing little grains of sand and small stones, the drill may be overloaded suddenly and the drill be powered off automatically. At this time, you need to pull out the drill right away and clean the hole you drilled before you start again. When you drill woof board and thick pitch, you also need to decrease pushing and drill slowly.
6.Taking out drill core
When you are going yo drill through the board or wal, you need to slow down, avoiding the drill bit being stuck. If the drill bit is stuck, you need to power off the drill immediately pull out the bit and clean it. Fetch out the drill core. Install the drill bit and start again.
Attention: You should be careful when taking out the drill bit, noting damaing it.
7.The drill vibrate
The drill vibrate when it is working.It may be because the distance between the racks connecting the lifting body and the stand is too big. Then you need to tighten the screws to adjust the distance. At the same time, you need to make sure that the pedestal and the stand is connected firmly.
Application:

This drill can be used on brick, stone, reinforced concrete, rock, and fireproof materials.

  • Water connection with hose approx.13ft
  • Overload protection / slip clutch
  • Aluminum base support
  • Use from -77℉
  • Drill bit Ø 4.25inch /13.7inch long
  • 1-1/4" BSP threaded connection for drill bits
  • 2 inch mandrel on stand for quick release
  • The biggest drill dual purpose
  • 2180W infinitely variable speeds
  • Non water seal cage reduce maintenance costs
  • Aluminum alloy material ligher and steadier
  • Max. drilling diameter 6inch
  • Suitable for sampling concrete, cement, brick, bituminous pavement and block
Specifications:
Model ZIZ-160 ZIZ-205 ZIZ-255
Supply voltage 110V/50~60 Hz 110V/50~60 Hz 110V/50~60 Hz
Rated power 2180W 3980W 4450W
Drilling capacity max. 160 mm max. 205 mm max. 255 mm
No-load speed 1600 U/min 750 U/min 580 U/min
Arbor size 1¼"UNC 1¼"UNC 1¼"UNC
Drill bit 108mm 108mm 108mm
Weight 18kg 26.9 kg 27.5kg
Packing size 75x20x25cm 85x35x20cm 100x25x35cm
Package Content:
  • 1 X Diamond Core Drill
  • 1 X Drill Bit(Φ108mm)
  • 1 X Ring Spanner
  • 1 X Monkey Wrench
  • 1 X Hose
  • 1 X Faucet Interface
  • 5 X Expansion Screws
  • 2 X Carbon Brushes
Our core drilling machine combines functionality and versatility in one device. It is ideal for lighter drilling work.

Installation:

First, install the screw connecting the stand and the pedestal. Before use the drill, you need to fix it.
1. Remove the two screws on the back of the stand;
2. Seperate the stand and the pedestal;
3. Rotate the pedesta 180° and install the screws.
4. Install completed

Fix the driller:

Here are two ways
1.Using expansion link
Choose a hollow tube according to the height of the place which need to be drilled. Put one end of the tube against the adjustable screw rod. And turn the rod reversely to fix the driller tightly, expansion bolts are not needed.
2.Using ecpansion bolt
Make a hole on the wall or the groud and install the bolt;
Expand the bolt;
Install the screw rod and the stand. Then tighten the nut.

Install drill bit

Before installing, you need to smear some grease on the drill end thread in order to discharge easily. After instlling, you need to run the driller at an idle state at first.
Attention: Before you install or remove the drill bot, you must be sure the drill is powered off. Before running, the drill must be connected with clean cold water.

Here are the ways to inject water:

1. Using tap water: Connecting the tap and the machine with the injecting hose.
2. Hanging a bucket over the drill
3. Using water pump
4.Drilling
Start the drill at an idle state. Then open the water tap. When there is water flowing from the drill, you can start drilling. At first, you need to drill slowly and increase strength gradually. After you drill deeper than 5mm, you can increase your push strength. If the drill's rotating speed decrease, than proves that the drill is overloaded. Then you need to decrease the push strength, avoiding the drill being stuck. If there is smoke coming out, you must pull out the drill right away and start to drill after a while, avoiding the engine being burn down.
5.Material being drilled
When drilling reinforced concrete, current increases and the drill will vibrate. Therefore, you need to decrease pushing strength but the decreasing amplitude should not be too big. Otherwise, the effiency will be affected and the drill bit will be worn more badly. When drilling reinforced concrete containing little grains of sand and small stones, the drill may be overloaded suddenly and the drill be powered off automatically. At this time, you need to pull out the drill right away and clean the hole you drilled before you start again. When you drill woof board and thick pitch, you also need to decrease pushing and drill slowly.
6.Taking out drill core
When you are going yo drill through the board or wal, you need to slow down, avoiding the drill bit being stuck. If the drill bit is stuck, you need to power off the drill immediately pull out the bit and clean it. Fetch out the drill core. Install the drill bit and start again.
Attention: You should be careful when taking out the drill bit, noting damaing it.
7.The drill vibrate
The drill vibrate when it is working.It may be because the distance between the racks connecting the lifting body and the stand is too big. Then you need to tighten the screws to adjust the distance. At the same time, you need to make sure that the pedestal and the stand is connected firmly.
Application:

This drill can be used on brick, stone, reinforced concrete, rock, and fireproof materials.

  • Water connection with hose approx.13ft
  • Overload protection / slip clutch
  • Aluminum base support
  • Use from -77℉
  • Drill bit Ø 4.25inch /13.7inch long
  • 1-1/4" BSP threaded connection for drill bits
  • 2 inch mandrel on stand for quick release
  • The biggest drill dual purpose
  • 2180W infinitely variable speeds
  • Non water seal cage reduce maintenance costs
  • Aluminum alloy material ligher and steadier
  • Max. drilling diameter 6inch
  • Suitable for sampling concrete, cement, brick, bituminous pavement and block
Specifications:
Model ZIZ-160 ZIZ-205 ZIZ-255
Supply voltage 110V/50~60 Hz 110V/50~60 Hz 110V/50~60 Hz
Rated power 2180W 3980W 4450W
Drilling capacity max. 160 mm max. 205 mm max. 255 mm
No-load speed 1600 U/min 750 U/min 580 U/min
Arbor size 1¼"UNC 1¼"UNC 1¼"UNC
Drill bit 108mm 108mm 108mm
Weight 18kg 26.9 kg 27.5kg
Packing size 75x20x25cm 85x35x20cm 100x25x35cm
Package Content:
  • 1 X Diamond Core Drill
  • 1 X Drill Bit(Φ108mm)
  • 1 X Ring Spanner
  • 1 X Monkey Wrench
  • 1 X Hose
  • 1 X Faucet Interface
  • 5 X Expansion Screws
  • 2 X Carbon Brushes

Shipping Policy

Shipping Fees

All the products are free shipping now, part of AK, HI, PW, MH, FM, VI, MP, AS, PR, GU States where remote place need addition shipping fees, no custom fees.

 

Note: Shipping time is influenced by the COVID-19, cargoes delivered time put off 3 days! Big cargoes( Please notice the size description or size photos that unilateral length more than 108'',  perimeter more than 165'' ) need 12 days delay.

Shipping Times

We adopt FedEx Ground、 UPS Ground、SAIA、RRTS、RLCARRIERS only ship orders within US, other country is not opened on this site, you can go to our other country site shop.

 

  • DELIVERY Days: 1-4 Business Days 
  • Processing Time: 3 Business Day
  • SHIP FROM CA & TX & KY & NJ WAREHOUSE

 

About Modification

Once your payment is completed, please inform by phone or E-mail if any modification is needed before we dispatch your package.

The customer will be responsible for all extra fees caused by address alternation if contact is made after item has been dispatched.

 

International Purchase

Import duties, taxes and charges are not included in item price or shipping charges. The buyer should be responsible for these charges.

 

 

Return Policy

Every single product is backed by a 12-months Warranty and a 30-day return policy from the date of purchase. Special circumstances will be listed clearly in the listing.

If you need to return a product and get a refund, please contact us for free shipping label and ship it back to us.

 

Satisfying Guarantee for Every Purchase

Dear customer, please contact us if you are not satisfied with a product before applying for return or refund. A prompt exchange should be issued within 30 days of delivery in original packaging and with proof of purchase from Vevor.

 

Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's related to man-made damage. If your item has been damaged in transit or become faulty in warranty period, please email us with pictures or video to show the problem.

 

  1. All returns must be pre-approved. Unauthorized returns will not be accepted.
  2. Check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.
  3. The same warranty is provided for replaced products as the returned ones.

 

If you are shipping the product

  1. Carefully pack the item(s) in original package.
  2. Stick the shipping label we offered on the outer
  3. Refund would be processed after the item is received by our warehouse staff, which is confirmed to be unopened and in good condition.
  4. For assistance on return, please message Vevor Facebook or send a message to: support@vevor.com.