2" Npt Brass Electric Solenoid Valve 2" Inch 22w High Pressure

2" Npt Brass Electric Solenoid Valve 2" Inch 22w High Pressure

Available: Out of Stock
Product SKU: NPTLWHTDCF/AC0001V1
$46.99 USD
Successful pre-order.Thanks for contacting us!
Brass Normally Closed Electric Solenoid Valve is constructed with a durable brass body, two-way inlet and outlet ports with two inch (2") female threaded (NPT) connections. Heat and oil resistant Viton gasket. It suitable for hot or cold water, air, very low viscosity fluids (< 20 cst), oils and hydrocarbons, such as gasoline, kerosene, or diesel fuel. It suitable for outdoor use, not for use underwater. Customers chose this general purpose valve for: do-it-yourself projects, moderately high temperature applications, harsh chemicals, flow control for irrigation systems, or reverse osmosis systems.
Leaving the valve powered on for long periods of time will reduce the life of the coil. Whenever possible the valve should be installed in a well ventilated are to increase the life of the coil. The valve is not intended to be left energized as a fail-safe for power outages. In this case please contact us for other options.
A pre-filter is always recommended to keep the diaphragm from debris and the valve functioning properly.

Install and use Attentions:
1. When install the solenoid valve, medium flow direction must be consistent with the direction arrow as shown in the valve body, the valve must be installed in horizontal pipe runs. Solenoid valve coil keep in a vertical position, this valve can not be put in these places what with the splashing water or water leakage. The 2A model can be used in the underwater environment.
2. Before installing the solenoid valve, pipeline should be cleaned thoroughly, the medium what crossing into the pipeline must be clean, viscosity<4°E.
3. Front the valve should be installed the 80-100 mesh /filter prevent the valve core be jammed, when the pressure be larger where after the valve, should be install the one-way valve. prevent the medium backflow or cause the solenoid valve closed lax.
4. In using should be regular cleaning dirt on the surface of the movable iron core and the piston, in dismounting should check the sealing gasket at the same time, when found damaged should be replaced timely.
5. This valve is unfavorable use in the explosive dangerous places. When need, please indicate in ordering.
6. Should be install the by-pass device, to ensure the normal production, for the solenoid valve needs change when the failure happens or need cleaning
7. According to the range of values from the scutcheon for choose power supply conditions and control its relay, place the down-lead of solenoid valve in the circuit, when Installing system, no grounding solenoid valve should be grounded, in order to ensure the safety.
  • Open and close quickly, stable performance, easy to use.
  • Connection – no polarity, "+" and "–" can be interchanged.
  • The valve timing is uncertain, however it is fast acting, less than one second.
  • 100% duty cycle – like most solenoid valves, the coil will become hot to the touch when left on continuously. The temperature will stabilize without failure.
  • Mounting position is preferably coil up but can be mounted in any position.

Specifications:
  • Body Material: Brass
  • Suitable Media: Water–Air-Gas-Etc
  • Components: Stainless Steel
  • Seal Material: NBR
  • Operation Type: Semi-Direct Lift Valve
  • Coil Connection: 5.5" Lead Wire
  • Voltage: 110V
  • Power Rating: 22W
  • Function: Normally Closed
  • Connection: 2” Inch FNPT
  • Temperature Range: 20–265°F
  • Pressure Range: 0–145 PSI
  • Power Requirements: 40VA-40W
  • Orifice Size: 50 mm
  • Cv Value: 48
  • Weight: 7.1 lbs
  • Height: 6.9"
  • Length: 5.3"
  • Width: 4.25"
  • 1 × Brass Normally Closed Electric Solenoid Valve

Brass Normally Closed Electric Solenoid Valve is constructed with a durable brass body, two-way inlet and outlet ports with two inch (2") female threaded (NPT) connections. Heat and oil resistant Viton gasket. It suitable for hot or cold water, air, very low viscosity fluids (< 20 cst), oils and hydrocarbons, such as gasoline, kerosene, or diesel fuel. It suitable for outdoor use, not for use underwater. Customers chose this general purpose valve for: do-it-yourself projects, moderately high temperature applications, harsh chemicals, flow control for irrigation systems, or reverse osmosis systems.
Leaving the valve powered on for long periods of time will reduce the life of the coil. Whenever possible the valve should be installed in a well ventilated are to increase the life of the coil. The valve is not intended to be left energized as a fail-safe for power outages. In this case please contact us for other options.
A pre-filter is always recommended to keep the diaphragm from debris and the valve functioning properly.

Install and use Attentions:
1. When install the solenoid valve, medium flow direction must be consistent with the direction arrow as shown in the valve body, the valve must be installed in horizontal pipe runs. Solenoid valve coil keep in a vertical position, this valve can not be put in these places what with the splashing water or water leakage. The 2A model can be used in the underwater environment.
2. Before installing the solenoid valve, pipeline should be cleaned thoroughly, the medium what crossing into the pipeline must be clean, viscosity<4°E.
3. Front the valve should be installed the 80-100 mesh /filter prevent the valve core be jammed, when the pressure be larger where after the valve, should be install the one-way valve. prevent the medium backflow or cause the solenoid valve closed lax.
4. In using should be regular cleaning dirt on the surface of the movable iron core and the piston, in dismounting should check the sealing gasket at the same time, when found damaged should be replaced timely.
5. This valve is unfavorable use in the explosive dangerous places. When need, please indicate in ordering.
6. Should be install the by-pass device, to ensure the normal production, for the solenoid valve needs change when the failure happens or need cleaning
7. According to the range of values from the scutcheon for choose power supply conditions and control its relay, place the down-lead of solenoid valve in the circuit, when Installing system, no grounding solenoid valve should be grounded, in order to ensure the safety.
  • Open and close quickly, stable performance, easy to use.
  • Connection – no polarity, "+" and "–" can be interchanged.
  • The valve timing is uncertain, however it is fast acting, less than one second.
  • 100% duty cycle – like most solenoid valves, the coil will become hot to the touch when left on continuously. The temperature will stabilize without failure.
  • Mounting position is preferably coil up but can be mounted in any position.

Specifications:
  • Body Material: Brass
  • Suitable Media: Water–Air-Gas-Etc
  • Components: Stainless Steel
  • Seal Material: NBR
  • Operation Type: Semi-Direct Lift Valve
  • Coil Connection: 5.5" Lead Wire
  • Voltage: 110V
  • Power Rating: 22W
  • Function: Normally Closed
  • Connection: 2” Inch FNPT
  • Temperature Range: 20–265°F
  • Pressure Range: 0–145 PSI
  • Power Requirements: 40VA-40W
  • Orifice Size: 50 mm
  • Cv Value: 48
  • Weight: 7.1 lbs
  • Height: 6.9"
  • Length: 5.3"
  • Width: 4.25"
  • 1 × Brass Normally Closed Electric Solenoid Valve

Shipping Policy

Shipping Fees

All the products are free shipping now, part of AK, HI, PW, MH, FM, VI, MP, AS, PR, GU States where remote place need addition shipping fees, no custom fees.

 

Note: Shipping time is influenced by the COVID-19, cargoes delivered time put off 3 days! Big cargoes( Please notice the size description or size photos that unilateral length more than 108'',  perimeter more than 165'' ) need 12 days delay.

Shipping Times

We adopt FedEx Ground、 UPS Ground、SAIA、RRTS、RLCARRIERS only ship orders within US, other country is not opened on this site, you can go to our other country site shop.

 

  • DELIVERY Days: 1-4 Business Days 
  • Processing Time: 3 Business Day
  • SHIP FROM CA & TX & KY & NJ WAREHOUSE

 

About Modification

Once your payment is completed, please inform by phone or E-mail if any modification is needed before we dispatch your package.

The customer will be responsible for all extra fees caused by address alternation if contact is made after item has been dispatched.

 

International Purchase

Import duties, taxes and charges are not included in item price or shipping charges. The buyer should be responsible for these charges.

 

 

Return Policy

Every single product is backed by a 12-months Warranty and a 30-day return policy from the date of purchase. Special circumstances will be listed clearly in the listing.

If you need to return a product and get a refund, please contact us for free shipping label and ship it back to us.

 

Satisfying Guarantee for Every Purchase

Dear customer, please contact us if you are not satisfied with a product before applying for return or refund. A prompt exchange should be issued within 30 days of delivery in original packaging and with proof of purchase from Vevor.

 

Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's related to man-made damage. If your item has been damaged in transit or become faulty in warranty period, please email us with pictures or video to show the problem.

 

  1. All returns must be pre-approved. Unauthorized returns will not be accepted.
  2. Check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.
  3. The same warranty is provided for replaced products as the returned ones.

 

If you are shipping the product

  1. Carefully pack the item(s) in original package.
  2. Stick the shipping label we offered on the outer
  3. Refund would be processed after the item is received by our warehouse staff, which is confirmed to be unopened and in good condition.
  4. For assistance on return, please message Vevor Facebook or send a message to: support@vevor.com.

Customer Reviews

Based on 4 reviews
75%
(3)
25%
(1)
0%
(0)
0%
(0)
0%
(0)
F
F.
Great solenoid valve. Great seller.

Ordered one of this solenoid valve. It came in really fast. Installed it on my well water storage tank. It works well for a while. Then it wouldn't shut off any more. Contacted the seller, she send me another one right way. The same problem. Contacted the seller again. She suspected there is stuff jammed in the valve. Opened it up, sure enough, there are big grain of sand stuck in there. Cleaned the sand away, the valve works again. Now I am putting a mesh filter before the valve.Great valve. Great seller. Great customer service. Will buy from this seller again and again!!!

R
R.E.
Solar panel bypass for nighttime

Great for my application

J
J.D.N.D.
38/5000 Perfect for the application required

38/5000Perfect for the application required.

G
G.S.
Solid design

Product works as designed. We use it to remotely empty our jacuzzi and refill it through Smartthings and this item was significantly cheaper than other competitors.