10 Head Ultrasonic Mist Maker Fogger Humidifier With Transformer 110V USA
Rated 3.5/5 based on 11 customer reviews

10 Head Ultrasonic Mist Maker Fogger Humidifier With Transformer 110V USA

Available: In Stock
Product SKU: 10TWHQ00000000001V1
Wishlist Compare
$134.99 USD
Image
  • Order within
This brand new 10 Head Ultrasonic mist maker can be used in many horticultural application including hydroponics, propagation, foliar feeding, grow room and greenhouse humidity generation, etc.
Usage step:
Place the nebulizer smoothly in a water container and inject an appropriate amount of clean water ( when the water level is lower than the water level sensor switch, the product will not spray; when the water is higher than water level sensor switch , the spray effect is not good. The nebulizer will generate heat in the working process, and water temperature will rise. It is recommended that this nebulizer should be used in the water container with good heat dissipation conditions.)
Plug the nebulizer power cord into an external DC power source. Turn on the power, the product can work normally.
Application:
1. Waterscape pool manufacturing fog
2. Spinning humidification
3. Tobacco humidification
4. Mushroom humidification
5. Greenhouse flowers humidification
6. Printed Electronics humidification
Kind Remind:
1. When the atomizer work, please do not put your hand over the top of the atomizer spray chamber to prevent ultrasonic wounded.
2. Nebulizer must be working in the water in order, before using the water and then put it in its power, and to ensure that there is water in a spray film surface state, in order to avoid damage to the nebulizer.
3. When you stop using the nebulizer before disconnect the power, then remove from the water atomizer.
4. When using the nebulizer, please use the output power of more than 250W, the output voltage is DC45 ± 5V supply.
5. When generating a plurality of atomizer is set using the same container, each with a separate power supply need not connect a plurality of the nebulizer for use with a single power supply, and note the respective atomizer are mutually conductive housing, in order to prevent the work galvanic corrosion.
6. Mist generated by the nebulizer must use fan forced discharge, and each group of nebulizer reserved 350CM2 of flat space, the water temperature is too high to avoid shortening the life of the nebulizer.
7. Nebulizer not suitable for corrosive liquid atomization, to avoid damage to the atomizer and atomized metal sheet.

8. Do not damaged during installation level sensor switch, switch failure caused the water level to prevent runaway nebulizer. Level switch should stop after the damage, otherwise there will be further damaged dry atomized piece atomizer. At this point in order to use the required repairs by qualified service personnel after a good.

Note:

Please don't input 220V to mist maker directly, you should input the voltage through transformer. Also, the power line is provided by yourself.


Features:
  • Atomized water quality and adaptable, the same nebulizer use pure water or tap water can work
  • The power for a wide range of products to ensure that the changes in the city still under normal use larger occasions
  • There boot delay circuit, to avoid a power surge current excessive damage to the line
  • A single sprinkler line using an independent design, and the use of over-current protection circuit, avoiding the burning of a nozzle damaged power lines, and does not affect the normal operation of other jets
  • The machine current voltage and temperature by less influence, because each nozzle current electronic automatic adjustment, the current increasing temperature will decrease (does not affect the amount of fog), to avoid serious power tube heat current increasing the vicious cycle and damage the atomizer
  • This product uses high thermal conductivity, high corrosion resistance, good mechanical strength of the metal shell, reducing the temperature difference between the water inside the host, thereby prolonging the life of the product

Specifications:
  • Shell material: Copper shell
  • Transformer Voltage: 110V

  • Humidifier Voltage: DC48V

  • Working current: 4.8A-5A
  • Output power: 250W
  • Spray volume: 3500- 5000ML / H
  • Cooling model: Air-cooled
  • Power line: 1.5 m
  • Water tempreture: 5-50°C (the normal tempreture is 30°C)
  • Water level: 6cm
  • Packing size: 320x125x180mm
  • Packing weight: 3 kg
Package Content:
  • 1 x 10 Head Ultrasonic Mist Maker
  • 1 x Transformer
This brand new 10 Head Ultrasonic mist maker can be used in many horticultural application including hydroponics, propagation, foliar feeding, grow room and greenhouse humidity generation, etc.
Usage step:
Place the nebulizer smoothly in a water container and inject an appropriate amount of clean water ( when the water level is lower than the water level sensor switch, the product will not spray; when the water is higher than water level sensor switch , the spray effect is not good. The nebulizer will generate heat in the working process, and water temperature will rise. It is recommended that this nebulizer should be used in the water container with good heat dissipation conditions.)
Plug the nebulizer power cord into an external DC power source. Turn on the power, the product can work normally.
Application:
1. Waterscape pool manufacturing fog
2. Spinning humidification
3. Tobacco humidification
4. Mushroom humidification
5. Greenhouse flowers humidification
6. Printed Electronics humidification
Kind Remind:
1. When the atomizer work, please do not put your hand over the top of the atomizer spray chamber to prevent ultrasonic wounded.
2. Nebulizer must be working in the water in order, before using the water and then put it in its power, and to ensure that there is water in a spray film surface state, in order to avoid damage to the nebulizer.
3. When you stop using the nebulizer before disconnect the power, then remove from the water atomizer.
4. When using the nebulizer, please use the output power of more than 250W, the output voltage is DC45 ± 5V supply.
5. When generating a plurality of atomizer is set using the same container, each with a separate power supply need not connect a plurality of the nebulizer for use with a single power supply, and note the respective atomizer are mutually conductive housing, in order to prevent the work galvanic corrosion.
6. Mist generated by the nebulizer must use fan forced discharge, and each group of nebulizer reserved 350CM2 of flat space, the water temperature is too high to avoid shortening the life of the nebulizer.
7. Nebulizer not suitable for corrosive liquid atomization, to avoid damage to the atomizer and atomized metal sheet.

8. Do not damaged during installation level sensor switch, switch failure caused the water level to prevent runaway nebulizer. Level switch should stop after the damage, otherwise there will be further damaged dry atomized piece atomizer. At this point in order to use the required repairs by qualified service personnel after a good.

Note:

Please don't input 220V to mist maker directly, you should input the voltage through transformer. Also, the power line is provided by yourself.


Features:
  • Atomized water quality and adaptable, the same nebulizer use pure water or tap water can work
  • The power for a wide range of products to ensure that the changes in the city still under normal use larger occasions
  • There boot delay circuit, to avoid a power surge current excessive damage to the line
  • A single sprinkler line using an independent design, and the use of over-current protection circuit, avoiding the burning of a nozzle damaged power lines, and does not affect the normal operation of other jets
  • The machine current voltage and temperature by less influence, because each nozzle current electronic automatic adjustment, the current increasing temperature will decrease (does not affect the amount of fog), to avoid serious power tube heat current increasing the vicious cycle and damage the atomizer
  • This product uses high thermal conductivity, high corrosion resistance, good mechanical strength of the metal shell, reducing the temperature difference between the water inside the host, thereby prolonging the life of the product

Specifications:
  • Shell material: Copper shell
  • Transformer Voltage: 110V

  • Humidifier Voltage: DC48V

  • Working current: 4.8A-5A
  • Output power: 250W
  • Spray volume: 3500- 5000ML / H
  • Cooling model: Air-cooled
  • Power line: 1.5 m
  • Water tempreture: 5-50°C (the normal tempreture is 30°C)
  • Water level: 6cm
  • Packing size: 320x125x180mm
  • Packing weight: 3 kg
Package Content:
  • 1 x 10 Head Ultrasonic Mist Maker
  • 1 x Transformer

Shipping Policy

Delivery Times

Package handling only takes 1 business day at our warehouse, so please make sure entering correct payment and shipping information before checking out.

We adopt FEDEX Ground ( UPS Ground ) to ship your orders.

FEDEX Ground ( UPS Ground ) : Shipping Time 3-7 business days.

 

 

About Modification

Once your payment is completed, please inform by phone or E-mail if any modification is needed before we dispatch your package.

The customer will be responsible for all extra fees caused by address alternation if contact is made after item has been dispatched.

International Purchase

Import duties, taxes and charges are not included in item price or shipping charges. The buyer should be responsible for these charges.

 

 

Return Policy

Every single product is backed by a 24-months Warranty and a 90-day return policy from the date of purchase. Special circumstances will be listed clearly in the listing.

If you need to return a product and get a refund, please contact us for free shipping label and ship it back to us.

 

Satisfying Guarantee for Every Purchase

Dear customer, please contact us if you are not satisfied with a product before applying for return or refund. A prompt exchange should be issued within 90 days of delivery in original packaging and with proof of purchase from Vevor.

 

Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's related to man-made damage. If your item has been damaged in transit or become faulty in warranty period, please email us with pictures or video to show the problem.

 

  1. All returns must be pre-approved. Unauthorized returns will not be accepted.
  2. Check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.
  3. The same warranty is provided for replaced products as the returned ones.

 

If you are shipping the product

  1. Carefully pack the item(s) in original package.
  2. Stick the shipping label we offered on the outer
  3. Refund would be processed after the item is received by our warehouse staff, which is confirmed to be unopened and in good condition.
  4. For assistance on return, please call Vevor on (916) 273-9717or send a message to: service@vevor.com.

Customer Reviews

No reviews yet
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Customer Reviews

No reviews yet
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)