![\"VEVOR](\"https:\/\/diy-ideas.oss-accelerate.aliyuncs.com\/wp-content\/uploads\/2023\/12\/vevor-ultrasonic-cleaner-models.png!webp\")
\n<\/figure>\n
Table of contents<\/h2>\n\n- Cautions<\/a><\/li>\n
- Specifications<\/a><\/li>\n
- Application<\/a><\/li>\n
- Product Drawing & Indication<\/a><\/li>\n
- Operation Procedure<\/a><\/li>\n
- Maintenance<\/a><\/li>\n
- FAQs About VEVOR Ultrasonic Cleaner<\/a><\/li>\n<\/ul>\n<\/div>\n
Application:<\/h3>\n
Electronic factories, car workshops, industrial and mining areas, laboratories, hospitals, dental clinics, watch shops, optical shops, jewelry shops, mobile phone repair shops, and household use.<\/p>\n
Cautions<\/h2>\n\n- Thanks for purchasing the ultrasonic cleaner. Please read the instruction manual carefully before operation to avoid damage to the machine or any danger to personal safety. And please keep it for reference.<\/li>\n
- Ensure the power supply is in the rated range before the power cable is connected. Refitting is strictly prohibited! Attention! The control panel will be eroded by organic solution, strong acid, and strong alkali!<\/li>\n
- Ensure the earth wiring is well-connected before starting.<\/li>\n
- Ensure the power key or knob is ON the \u2018OFF\u2019 place before starting.
\n Do not operate if the tank is empty, or the ultrasonic generator will be damaged. If heating is needed, the water level shouldn\u2019t be less than 2\/3.<\/li>\n - Please close the lid to reduce noise and pay attention to water and steam in case of burning skin while open the lid.<\/li>\n
- Do not relocate the machine when fluid is in the tank in case of overflow.
\n Suggest using water-soluble liquid for benchtop ultrasonic cleaners. Strong acid or flammability cleaner is forbidden.<\/li>\n - Do not use the machine in severe environments:\n
\n- Where temperature changes fiercely:<\/li>\n
- Where the humidity is too high and is easy to produce dew;<\/li>\n
- The place where vibration or impact is strong;<\/li>\n
- The place where exists corrosive gas or dust;<\/li>\n
- The place where water, oil, or chemicals splash;<\/li>\n
- The place where is filled with explosive and flammable gas.<\/li>\n<\/ul>\n<\/li>\n
- Shorten the daily working time. A suggestion is to stop for a few minutes for heat dissipation after working over 30 minutes.<\/li>\n<\/ul>\n
\u25b2 Heater is forbidden when using flammable liquid (such as alcohol, solvent cleaner, etc.) to clean objects. The cleaning effect will be much better if using the machine together with the proper solvent.<\/strong><\/p>\nSpecifications<\/h2>\n\n ![\"VEVOR](\"https:\/\/diy-ideas.oss-accelerate.aliyuncs.com\/wp-content\/uploads\/2023\/12\/vevor-ultrasonic-cleaner-specifications-1024x342.png!webp\")
\n<\/figure>\n\n ![\"VEVOR](\"https:\/\/diy-ideas.oss-accelerate.aliyuncs.com\/wp-content\/uploads\/2023\/12\/vevor-ultrasonic-cleaner-product-specifications-1024x421.png!webp\")
\n<\/figure>\nApplication<\/h2>\n
PCB, jewelry, electronic components, car parts, hardware, metal tools, computer parts, Laboratory instruments, clocks & watches, eyeglasses, contact lenses, dentures, dental tools, DVD & VCD, golf, table-ware, printer inkjet, seal and comb, toothbrush, coins, etc.<\/p>\n\n\n\n\nIndustry<\/td>\n The Cleaning Products & Materials<\/td>\n Clear Dirt<\/td>\n<\/tr>\n \nIntegrated circuit, power tube, silicon wafer, diode, lead frame, capillary, tray, etc.<\/td>\n Tube parts, cathode ray tube, printed circuit board, quartz parts, electronic components, telephone switching equipment, speaker components, power meter, LCD glass, core iron parts, computer floppy disk, video parts, hoop parts, head, photo die mask, etc.<\/td>\n Hards, etching oil, stamping oil, polishing wax, dust particles, etc<\/td>\n<\/tr>\n \n Electrical & electronic machine<\/td>\n Fingerprint, powder, cutting oil, stamping oil, iron filings, polishing materials, walnut powder, polishing wax, resin, dust, etc.<\/td>\n Fingerprint, powder, cutting oil,stamping oil, iron filings, polishing materials, walnut powder, polishing wax, resin, dust, etc.<\/td>\n<\/tr>\n \nPrecision machine<\/td>\n Glasses, lenses, prism, optical lenses, filter lenses, glass devices, film, optical fiber, etc.<\/td>\n Machine cutting oil, iron filings, polishing powder, oil, grease, dirt, etc.<\/td>\n<\/tr>\n \nOptical device<\/td>\n Medical instruments, dentures, etc.<\/td>\n Plastic, resin, paraffin, fingerprinting, etc.<\/td>\n<\/tr>\n \nHardware &machinery parts<\/td>\n Iron filings, polishing powder, oil, stamping oil, dirt, etc.<\/td>\n Iron filings, polishing powder, oil, stamping oil, dirt, etc.<\/td>\n<\/tr>\n \nMedical instrument<\/td>\n Bearing, gear, ball, metal shaft parts, tools, adjustable valve and cylinder parts, burner, compressors, hydraulic press, gun and ultracentrifuge, city water faucet, etc.<\/td>\n Piston ring, carburetor, flow meter housing, compressor shell, electrical components, etc.<\/td>\n<\/tr>\n \nElectroplate<\/td>\n Galvanized parts, mold, stamping parts, etc.<\/td>\n Chemical colloid, glue, and other solid material, dust, etc.<\/td>\n<\/tr>\n \nCar parts<\/td>\n Chemical or artificial fiber nozzle filter protector chemical fiber texture, etc.<\/td>\n Bearing, sewing machine parts, typewriters, textile machines, optical-mechanical devices, gas valves, watches, cameras, metal filter elements, etc.<\/td>\n<\/tr>\n \n Chemical fiber<\/td>\n Polishing scrap iron, oil, blackiron shell, rust, oxidation shell,scrap iron, polishing powder, stamping oil, dirt, etc.<\/td>\n Polishing scrap iron, oil, blackiron shell, rust, oxidation shell, scrap iron, polishing powder, stamping oil, dirt, etc.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/figure>\nProduct Drawing & Indication<\/h2>\n\n ![\"VEVOR](\"https:\/\/diy-ideas.oss-accelerate.aliyuncs.com\/wp-content\/uploads\/2023\/12\/vevor-ultrasonic-cleaner-mechanical-model-1024x444.png!webp\")
\n<\/figure>\n\n ![\"VEVOR](\"https:\/\/diy-ideas.oss-accelerate.aliyuncs.com\/wp-content\/uploads\/2023\/12\/vevor-ultrasonic-cleaner-digital-model-1024x444.png!webp\")
\n<\/figure>\nOperation Procedure<\/h2>\n\n- Before starting the equipment, check the machine to see if there are loosened parts.<\/li>\n
- Keep the unit on a stable and flat working platform in a dry and cool environment.<\/li>\n
- According to the size and quantity of washing objects, add a little bit of detergent in the tank, which can help improve the cleaning effect. (Empty tank working is forbidden!<\/em>)
![](\"https:\/\/lh7-us.googleusercontent.com\/B80jPUPPZ2EWx1LUuk48IMofOnI55mQ1zlFq8CTmmGjnAa5dk5WBHXAlbHkpxDydyq1f3dV6WWZ_JKbcV1UZ5BQSjZVEviSew1Ev2rS35zs-DO-4r4rlZuRkmXFYYQBs9DJDnvqkoiq2wKQU2a87zb8\")
<\/li>\n- Ensure the correct power and switch connection before starting the equipment.<\/li>\n<\/ul>\n
\u25a0 Operation Instructions:(Mechanical models)<\/strong><\/p>\n \u25c7 Start (ULTRASONIC<\/strong>), clockwise rotate to choose the time you require between 0~30 min. When the indicator light is on and makes a \u201cZI ZI\u201d sound, it shows ultrasonic operation works OK.<\/p>\n\u25c7 If needs heating, start (HEATING)to adjust the required temperature, normally 40~60\u2103 is the best. (Heating is optional upon need)<\/p>\n
\u25c7 To stop cleaning;<\/p>\n
\u2460 Press OFF once, the ultrasonic stop runs, and the indicator light will also be off.<\/p>\n
\u2461 Rotate the heating control knob to\u201cOFF\u201d, the indicator light will also be off.<\/p>\n
\u2462 Then switch off the unit and disconnect the power.<\/p>\n
\u2463 Empty the liquid and clean the tank and the unit with a clean cloth for next use.<\/p>\n
\u25a0 Operation Instructions:(Digital models)<\/strong><\/p>\n\u25c7 Timer setting: When power is connected, the default setting is\u201c05:00\u201d. Press TEME+<\/strong>once will increase time by 1 min; Press TEME+<\/strong>once will decrease time by 1 min. (Free choice and digital countdown control).<\/p>\n\u25c7 Temperature setting: (heating is optional upon needs): When power is connected, the default setting is \u201c50\u2103\u201d and the Actual is room temp., press TEMP+<\/strong>once, will increase temperature by 1\u2103; Press TEMP-once, will decrease temperature by 1\u2103. If the setting temperature is slower than the actual tank temperature, the operation will stop automatically. When the temperature rises to the setting temperature, the indicating light goes off. When ultrasonic work, two temperature screens show the set temperature and actual temperature that has been reached.<\/p>\n\u25c7 After setting the time and temperature, press ON\/OFF once, the equipment will work automatically. Press ON\/OFF again, and the work process will stop. Then switch off the unit and disconnect the power supply, empty out the liquid, and clean the tank and the unit with a clean cloth for next use.<\/p>\n
\u25a0 Adjusting power:<\/p>\n
\u25c7 The function is only available for power-adjustable models! Rotate SLOWLY the power knob clockwise to increase the power from 40% to 100%, and counter-clockwise SLOWLY to decrease sonic power.<\/p>\n
Maintenance<\/h2>\nMaintenance<\/h3>\n
\u25a0 The unit must be opened by an authorized specialized person only for maintenance and care of it.<\/p>\n
\u25a0 Clean the contaminant in the tank frequently.<\/p>\n
Trouble clearing<\/h3>\n\n\n\n\nNo.<\/td>\n Problems<\/td>\n Possible causes<\/td>\n Solutions<\/td>\n Remarks<\/td>\n<\/tr>\n \n1<\/td>\n No ultrasonic<\/td>\n A. Loosen or tighten the screw.
\n B. Replace timer or digital panel.C. Inquiry our after-service engineer.<\/td>\n A. Loosen or tighten the screw.
\n B. Replace the timer or digital panel.
\n C. Inquiry our after-service engineer.<\/td>\n <\/td>\n<\/tr>\n \n2<\/td>\n A. Check the heating plug and connect it well, check the outlet line with the multimeter: if OK and the resistance value is a few hundred OHMs.B. Change the same specification fuse.C. Replace the bad heating pad if the open circuit. D. Check the broken part and change it. E. Inquiry our after-service engineer.<\/td>\n Time control failure<\/td>\n A. Check the heating plug and connect it well, check the outlet line with the multimeter: if OK and the resistance value is a few hundred OHMs.
\n B. Change the same specification fuse.
\n C. Replace the bad heating pad if the open circuit.
\n D. Check the broken part and change it.
\n E. Inquiry our after-service engineer.<\/td>\n <\/td>\n<\/tr>\n \n3<\/td>\n No heating<\/td>\n A. Heater power switch badlinkage.
\n B. Fuse burnout.
\n C. Heating pad burnout.
\n D. Digital display board out of control.
\n E. Other reasons<\/td>\n A. Check the heating plug and connect it well, check the outlet line with the multimeter: if OK and the resistance value is a few hundred OHMs.
\n B. Change the same specification fuse.
\n C. Replace the bad heating pad if the open circuit.
\n D. Check the broken part and change it.
\n E. Inquiry our after-service engineer.<\/td>\n Suggestion50-60\u2103 <\/td>\n<\/tr>\n \n4<\/td>\n Temperaturecontrol failure<\/td>\n Temperature control failure<\/td>\n A. Fasten the thermostat header.
\n B. Replace the thermostat.
\n C. Check the broken part and change it.
\n D. Inquiry our after-service engineer.<\/td>\n <\/td>\n<\/tr>\n \n5<\/td>\n Not well cleaning<\/td>\n A. Connect the ultrasonic button and adjust.
\n B. Adjust the liquid to the best surface.
\n C. Adjust the temperature to the most fitted.
\n D. Stop and switch off the power supply, and replace suitable liquid after the previous liquid cools down.
\n E. Inquiry our after-service engineer.<\/td>\n A. To ensure grounded.
\n B. Check if the machine earth wire loosen.<\/td>\n Suggestion50-60\u2103 <\/td>\n<\/tr>\n \n6<\/td>\n Electric leakage<\/td>\n A. Customer side not grounded.
\n B. Machine not grounded<\/td>\n A. To ensure grounded.
\n B. Check if the machine earth wire loosens.<\/td>\n <\/td>\n<\/tr>\n \n7<\/td>\n Other problems<\/td>\n <\/td>\n <\/td>\n <\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/figure>\nFAQs About VEVOR Ultrasonic Cleaner<\/h2>\nQ1: How do I set up my VEVOR Ultrasonic Cleaner for the first time?<\/h3>\n
A1: Begin by placing your cleaner on a stable, level surface. Fill the tank with water, ensuring it\u2019s within the recommended level. Add the appropriate cleaning solution, set the temperature and timer, and you\u2019re ready to start.<\/p>\n
Q2: What items should I avoid cleaning in the ultrasonic cleaner?<\/h3>\n
A2: Avoid cleaning delicate items like pearls, emeralds, and items with loose settings or cracked surfaces. Always check the item\u2019s compatibility with ultrasonic cleaning before proceeding.<\/p>\n
Q3: How can I troubleshoot common issues with my ultrasonic cleaner?<\/h3>\n
A3: If you encounter issues, ensure the cleaner is properly plugged in and the settings are correctly adjusted. Check for any obstructions in the tank and ensure the cleaning solution is appropriate for the items being cleaned.<\/p>\n
Q4: How often should I change the cleaning solution in my ultrasonic cleaner?<\/h3>\n
A4: Change the solution after every cleaning session or when it becomes visibly dirty. Regular changing of the solution ensures optimal cleaning efficiency.<\/p>\n
Q5: Can I use tap water in my VEVOR Ultrasonic Cleaner?<\/h3>\n
A5: Yes, tap water can be used, but for enhanced cleaning performance, especially for more delicate items, using distilled water is recommended.<\/p>\n
Final Words<\/h2>\n
The VEVOR Ultrasonic Cleaner Instruction Manual is your go-to resource for leveraging the full potential of your ultrasonic cleaner. From setup to maintenance, this guide ensures a seamless and effective cleaning experience. Remember, regular care and correct usage are key to the longevity and efficiency of your VEVOR Ultras<\/a>o<\/a>nic Cleaner<\/a>. Ready to experience the ultimate cleaning solution? Explore our range of VEVOR Ultrasonic Cleaners and elevate your cleaning standards today.<\/p>\n
Application:<\/h3>\n
Electronic factories, car workshops, industrial and mining areas, laboratories, hospitals, dental clinics, watch shops, optical shops, jewelry shops, mobile phone repair shops, and household use.<\/p>\n
Cautions<\/h2>\n\n- Thanks for purchasing the ultrasonic cleaner. Please read the instruction manual carefully before operation to avoid damage to the machine or any danger to personal safety. And please keep it for reference.<\/li>\n
- Ensure the power supply is in the rated range before the power cable is connected. Refitting is strictly prohibited! Attention! The control panel will be eroded by organic solution, strong acid, and strong alkali!<\/li>\n
- Ensure the earth wiring is well-connected before starting.<\/li>\n
- Ensure the power key or knob is ON the \u2018OFF\u2019 place before starting.
\n Do not operate if the tank is empty, or the ultrasonic generator will be damaged. If heating is needed, the water level shouldn\u2019t be less than 2\/3.<\/li>\n - Please close the lid to reduce noise and pay attention to water and steam in case of burning skin while open the lid.<\/li>\n
- Do not relocate the machine when fluid is in the tank in case of overflow.
\n Suggest using water-soluble liquid for benchtop ultrasonic cleaners. Strong acid or flammability cleaner is forbidden.<\/li>\n - Do not use the machine in severe environments:\n
\n- Where temperature changes fiercely:<\/li>\n
- Where the humidity is too high and is easy to produce dew;<\/li>\n
- The place where vibration or impact is strong;<\/li>\n
- The place where exists corrosive gas or dust;<\/li>\n
- The place where water, oil, or chemicals splash;<\/li>\n
- The place where is filled with explosive and flammable gas.<\/li>\n<\/ul>\n<\/li>\n
- Shorten the daily working time. A suggestion is to stop for a few minutes for heat dissipation after working over 30 minutes.<\/li>\n<\/ul>\n
\u25b2 Heater is forbidden when using flammable liquid (such as alcohol, solvent cleaner, etc.) to clean objects. The cleaning effect will be much better if using the machine together with the proper solvent.<\/strong><\/p>\nSpecifications<\/h2>\n\n
\n<\/figure>\n\n
\n<\/figure>\nApplication<\/h2>\n
PCB, jewelry, electronic components, car parts, hardware, metal tools, computer parts, Laboratory instruments, clocks & watches, eyeglasses, contact lenses, dentures, dental tools, DVD & VCD, golf, table-ware, printer inkjet, seal and comb, toothbrush, coins, etc.<\/p>\n\n\n\n\nIndustry<\/td>\n The Cleaning Products & Materials<\/td>\n Clear Dirt<\/td>\n<\/tr>\n \nIntegrated circuit, power tube, silicon wafer, diode, lead frame, capillary, tray, etc.<\/td>\n Tube parts, cathode ray tube, printed circuit board, quartz parts, electronic components, telephone switching equipment, speaker components, power meter, LCD glass, core iron parts, computer floppy disk, video parts, hoop parts, head, photo die mask, etc.<\/td>\n Hards, etching oil, stamping oil, polishing wax, dust particles, etc<\/td>\n<\/tr>\n \n Electrical & electronic machine<\/td>\n Fingerprint, powder, cutting oil, stamping oil, iron filings, polishing materials, walnut powder, polishing wax, resin, dust, etc.<\/td>\n Fingerprint, powder, cutting oil,stamping oil, iron filings, polishing materials, walnut powder, polishing wax, resin, dust, etc.<\/td>\n<\/tr>\n \nPrecision machine<\/td>\n Glasses, lenses, prism, optical lenses, filter lenses, glass devices, film, optical fiber, etc.<\/td>\n Machine cutting oil, iron filings, polishing powder, oil, grease, dirt, etc.<\/td>\n<\/tr>\n \nOptical device<\/td>\n Medical instruments, dentures, etc.<\/td>\n Plastic, resin, paraffin, fingerprinting, etc.<\/td>\n<\/tr>\n \nHardware &machinery parts<\/td>\n Iron filings, polishing powder, oil, stamping oil, dirt, etc.<\/td>\n Iron filings, polishing powder, oil, stamping oil, dirt, etc.<\/td>\n<\/tr>\n \nMedical instrument<\/td>\n Bearing, gear, ball, metal shaft parts, tools, adjustable valve and cylinder parts, burner, compressors, hydraulic press, gun and ultracentrifuge, city water faucet, etc.<\/td>\n Piston ring, carburetor, flow meter housing, compressor shell, electrical components, etc.<\/td>\n<\/tr>\n \nElectroplate<\/td>\n Galvanized parts, mold, stamping parts, etc.<\/td>\n Chemical colloid, glue, and other solid material, dust, etc.<\/td>\n<\/tr>\n \nCar parts<\/td>\n Chemical or artificial fiber nozzle filter protector chemical fiber texture, etc.<\/td>\n Bearing, sewing machine parts, typewriters, textile machines, optical-mechanical devices, gas valves, watches, cameras, metal filter elements, etc.<\/td>\n<\/tr>\n \n Chemical fiber<\/td>\n Polishing scrap iron, oil, blackiron shell, rust, oxidation shell,scrap iron, polishing powder, stamping oil, dirt, etc.<\/td>\n Polishing scrap iron, oil, blackiron shell, rust, oxidation shell, scrap iron, polishing powder, stamping oil, dirt, etc.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/figure>\nProduct Drawing & Indication<\/h2>\n\n
\n<\/figure>\n\n
\n<\/figure>\nOperation Procedure<\/h2>\n\n- Before starting the equipment, check the machine to see if there are loosened parts.<\/li>\n
- Keep the unit on a stable and flat working platform in a dry and cool environment.<\/li>\n
- According to the size and quantity of washing objects, add a little bit of detergent in the tank, which can help improve the cleaning effect. (Empty tank working is forbidden!<\/em>)<\/li>\n
- Ensure the correct power and switch connection before starting the equipment.<\/li>\n<\/ul>\n
\u25a0 Operation Instructions:(Mechanical models)<\/strong><\/p>\n \u25c7 Start (ULTRASONIC<\/strong>), clockwise rotate to choose the time you require between 0~30 min. When the indicator light is on and makes a \u201cZI ZI\u201d sound, it shows ultrasonic operation works OK.<\/p>\n\u25c7 If needs heating, start (HEATING)to adjust the required temperature, normally 40~60\u2103 is the best. (Heating is optional upon need)<\/p>\n
\u25c7 To stop cleaning;<\/p>\n
\u2460 Press OFF once, the ultrasonic stop runs, and the indicator light will also be off.<\/p>\n
\u2461 Rotate the heating control knob to\u201cOFF\u201d, the indicator light will also be off.<\/p>\n
\u2462 Then switch off the unit and disconnect the power.<\/p>\n
\u2463 Empty the liquid and clean the tank and the unit with a clean cloth for next use.<\/p>\n
\u25a0 Operation Instructions:(Digital models)<\/strong><\/p>\n\u25c7 Timer setting: When power is connected, the default setting is\u201c05:00\u201d. Press TEME+<\/strong>once will increase time by 1 min; Press TEME+<\/strong>once will decrease time by 1 min. (Free choice and digital countdown control).<\/p>\n\u25c7 Temperature setting: (heating is optional upon needs): When power is connected, the default setting is \u201c50\u2103\u201d and the Actual is room temp., press TEMP+<\/strong>once, will increase temperature by 1\u2103; Press TEMP-once, will decrease temperature by 1\u2103. If the setting temperature is slower than the actual tank temperature, the operation will stop automatically. When the temperature rises to the setting temperature, the indicating light goes off. When ultrasonic work, two temperature screens show the set temperature and actual temperature that has been reached.<\/p>\n\u25c7 After setting the time and temperature, press ON\/OFF once, the equipment will work automatically. Press ON\/OFF again, and the work process will stop. Then switch off the unit and disconnect the power supply, empty out the liquid, and clean the tank and the unit with a clean cloth for next use.<\/p>\n
\u25a0 Adjusting power:<\/p>\n
\u25c7 The function is only available for power-adjustable models! Rotate SLOWLY the power knob clockwise to increase the power from 40% to 100%, and counter-clockwise SLOWLY to decrease sonic power.<\/p>\n
Maintenance<\/h2>\nMaintenance<\/h3>\n
\u25a0 The unit must be opened by an authorized specialized person only for maintenance and care of it.<\/p>\n
\u25a0 Clean the contaminant in the tank frequently.<\/p>\n
Trouble clearing<\/h3>\n\n\n\n\nNo.<\/td>\n Problems<\/td>\n Possible causes<\/td>\n Solutions<\/td>\n Remarks<\/td>\n<\/tr>\n \n1<\/td>\n No ultrasonic<\/td>\n A. Loosen or tighten the screw.
\n B. Replace timer or digital panel.C. Inquiry our after-service engineer.<\/td>\n A. Loosen or tighten the screw.
\n B. Replace the timer or digital panel.
\n C. Inquiry our after-service engineer.<\/td>\n <\/td>\n<\/tr>\n \n2<\/td>\n A. Check the heating plug and connect it well, check the outlet line with the multimeter: if OK and the resistance value is a few hundred OHMs.B. Change the same specification fuse.C. Replace the bad heating pad if the open circuit. D. Check the broken part and change it. E. Inquiry our after-service engineer.<\/td>\n Time control failure<\/td>\n A. Check the heating plug and connect it well, check the outlet line with the multimeter: if OK and the resistance value is a few hundred OHMs.
\n B. Change the same specification fuse.
\n C. Replace the bad heating pad if the open circuit.
\n D. Check the broken part and change it.
\n E. Inquiry our after-service engineer.<\/td>\n <\/td>\n<\/tr>\n \n3<\/td>\n No heating<\/td>\n A. Heater power switch badlinkage.
\n B. Fuse burnout.
\n C. Heating pad burnout.
\n D. Digital display board out of control.
\n E. Other reasons<\/td>\n A. Check the heating plug and connect it well, check the outlet line with the multimeter: if OK and the resistance value is a few hundred OHMs.
\n B. Change the same specification fuse.
\n C. Replace the bad heating pad if the open circuit.
\n D. Check the broken part and change it.
\n E. Inquiry our after-service engineer.<\/td>\n Suggestion50-60\u2103 <\/td>\n<\/tr>\n \n4<\/td>\n Temperaturecontrol failure<\/td>\n Temperature control failure<\/td>\n A. Fasten the thermostat header.
\n B. Replace the thermostat.
\n C. Check the broken part and change it.
\n D. Inquiry our after-service engineer.<\/td>\n <\/td>\n<\/tr>\n \n5<\/td>\n Not well cleaning<\/td>\n A. Connect the ultrasonic button and adjust.
\n B. Adjust the liquid to the best surface.
\n C. Adjust the temperature to the most fitted.
\n D. Stop and switch off the power supply, and replace suitable liquid after the previous liquid cools down.
\n E. Inquiry our after-service engineer.<\/td>\n A. To ensure grounded.
\n B. Check if the machine earth wire loosen.<\/td>\n Suggestion50-60\u2103 <\/td>\n<\/tr>\n \n6<\/td>\n Electric leakage<\/td>\n A. Customer side not grounded.
\n B. Machine not grounded<\/td>\n A. To ensure grounded.
\n B. Check if the machine earth wire loosens.<\/td>\n <\/td>\n<\/tr>\n \n7<\/td>\n Other problems<\/td>\n <\/td>\n <\/td>\n <\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/figure>\nFAQs About VEVOR Ultrasonic Cleaner<\/h2>\nQ1: How do I set up my VEVOR Ultrasonic Cleaner for the first time?<\/h3>\n
A1: Begin by placing your cleaner on a stable, level surface. Fill the tank with water, ensuring it\u2019s within the recommended level. Add the appropriate cleaning solution, set the temperature and timer, and you\u2019re ready to start.<\/p>\n
Q2: What items should I avoid cleaning in the ultrasonic cleaner?<\/h3>\n
A2: Avoid cleaning delicate items like pearls, emeralds, and items with loose settings or cracked surfaces. Always check the item\u2019s compatibility with ultrasonic cleaning before proceeding.<\/p>\n
Q3: How can I troubleshoot common issues with my ultrasonic cleaner?<\/h3>\n
A3: If you encounter issues, ensure the cleaner is properly plugged in and the settings are correctly adjusted. Check for any obstructions in the tank and ensure the cleaning solution is appropriate for the items being cleaned.<\/p>\n
Q4: How often should I change the cleaning solution in my ultrasonic cleaner?<\/h3>\n
A4: Change the solution after every cleaning session or when it becomes visibly dirty. Regular changing of the solution ensures optimal cleaning efficiency.<\/p>\n
Q5: Can I use tap water in my VEVOR Ultrasonic Cleaner?<\/h3>\n
A5: Yes, tap water can be used, but for enhanced cleaning performance, especially for more delicate items, using distilled water is recommended.<\/p>\n
Final Words<\/h2>\n
The VEVOR Ultrasonic Cleaner Instruction Manual is your go-to resource for leveraging the full potential of your ultrasonic cleaner. From setup to maintenance, this guide ensures a seamless and effective cleaning experience. Remember, regular care and correct usage are key to the longevity and efficiency of your VEVOR Ultras<\/a>o<\/a>nic Cleaner<\/a>. Ready to experience the ultimate cleaning solution? Explore our range of VEVOR Ultrasonic Cleaners and elevate your cleaning standards today.<\/p>\n
\n Do not operate if the tank is empty, or the ultrasonic generator will be damaged. If heating is needed, the water level shouldn\u2019t be less than 2\/3.<\/li>\n
\n Suggest using water-soluble liquid for benchtop ultrasonic cleaners. Strong acid or flammability cleaner is forbidden.<\/li>\n
- \n
- Where temperature changes fiercely:<\/li>\n
- Where the humidity is too high and is easy to produce dew;<\/li>\n
- The place where vibration or impact is strong;<\/li>\n
- The place where exists corrosive gas or dust;<\/li>\n
- The place where water, oil, or chemicals splash;<\/li>\n
- The place where is filled with explosive and flammable gas.<\/li>\n<\/ul>\n<\/li>\n
- Shorten the daily working time. A suggestion is to stop for a few minutes for heat dissipation after working over 30 minutes.<\/li>\n<\/ul>\n
\u25b2 Heater is forbidden when using flammable liquid (such as alcohol, solvent cleaner, etc.) to clean objects. The cleaning effect will be much better if using the machine together with the proper solvent.<\/strong><\/p>\n
Specifications<\/h2>\n
\n
\n<\/figure>\n\n
\n<\/figure>\nApplication<\/h2>\n
PCB, jewelry, electronic components, car parts, hardware, metal tools, computer parts, Laboratory instruments, clocks & watches, eyeglasses, contact lenses, dentures, dental tools, DVD & VCD, golf, table-ware, printer inkjet, seal and comb, toothbrush, coins, etc.<\/p>\n
\n\n\n
\n Industry<\/td>\n The Cleaning Products & Materials<\/td>\n Clear Dirt<\/td>\n<\/tr>\n \n Integrated circuit, power tube, silicon wafer, diode, lead frame, capillary, tray, etc.<\/td>\n Tube parts, cathode ray tube, printed circuit board, quartz parts, electronic components, telephone switching equipment, speaker components, power meter, LCD glass, core iron parts, computer floppy disk, video parts, hoop parts, head, photo die mask, etc.<\/td>\n Hards, etching oil, stamping oil, polishing wax, dust particles, etc<\/td>\n<\/tr>\n \n Electrical & electronic machine<\/td>\n Fingerprint, powder, cutting oil, stamping oil, iron filings, polishing materials, walnut powder, polishing wax, resin, dust, etc.<\/td>\n Fingerprint, powder, cutting oil,stamping oil, iron filings, polishing materials, walnut powder, polishing wax, resin, dust, etc.<\/td>\n<\/tr>\n \n Precision machine<\/td>\n Glasses, lenses, prism, optical lenses, filter lenses, glass devices, film, optical fiber, etc.<\/td>\n Machine cutting oil, iron filings, polishing powder, oil, grease, dirt, etc.<\/td>\n<\/tr>\n \n Optical device<\/td>\n Medical instruments, dentures, etc.<\/td>\n Plastic, resin, paraffin, fingerprinting, etc.<\/td>\n<\/tr>\n \n Hardware &machinery parts<\/td>\n Iron filings, polishing powder, oil, stamping oil, dirt, etc.<\/td>\n Iron filings, polishing powder, oil, stamping oil, dirt, etc.<\/td>\n<\/tr>\n \n Medical instrument<\/td>\n Bearing, gear, ball, metal shaft parts, tools, adjustable valve and cylinder parts, burner, compressors, hydraulic press, gun and ultracentrifuge, city water faucet, etc.<\/td>\n Piston ring, carburetor, flow meter housing, compressor shell, electrical components, etc.<\/td>\n<\/tr>\n \n Electroplate<\/td>\n Galvanized parts, mold, stamping parts, etc.<\/td>\n Chemical colloid, glue, and other solid material, dust, etc.<\/td>\n<\/tr>\n \n Car parts<\/td>\n Chemical or artificial fiber nozzle filter protector chemical fiber texture, etc.<\/td>\n Bearing, sewing machine parts, typewriters, textile machines, optical-mechanical devices, gas valves, watches, cameras, metal filter elements, etc.<\/td>\n<\/tr>\n \n Chemical fiber<\/td>\n Polishing scrap iron, oil, blackiron shell, rust, oxidation shell,scrap iron, polishing powder, stamping oil, dirt, etc.<\/td>\n Polishing scrap iron, oil, blackiron shell, rust, oxidation shell, scrap iron, polishing powder, stamping oil, dirt, etc.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/figure>\n Product Drawing & Indication<\/h2>\n
\n
\n<\/figure>\n\n
\n<\/figure>\nOperation Procedure<\/h2>\n
- \n
- Before starting the equipment, check the machine to see if there are loosened parts.<\/li>\n
- Keep the unit on a stable and flat working platform in a dry and cool environment.<\/li>\n
- According to the size and quantity of washing objects, add a little bit of detergent in the tank, which can help improve the cleaning effect. (Empty tank working is forbidden!<\/em>)
- Ensure the correct power and switch connection before starting the equipment.<\/li>\n<\/ul>\n
\u25a0 Operation Instructions:(Mechanical models)<\/strong><\/p>\n
\u25c7 Start (ULTRASONIC<\/strong>), clockwise rotate to choose the time you require between 0~30 min. When the indicator light is on and makes a \u201cZI ZI\u201d sound, it shows ultrasonic operation works OK.<\/p>\n
\u25c7 If needs heating, start (HEATING)to adjust the required temperature, normally 40~60\u2103 is the best. (Heating is optional upon need)<\/p>\n
\u25c7 To stop cleaning;<\/p>\n
\u2460 Press OFF once, the ultrasonic stop runs, and the indicator light will also be off.<\/p>\n
\u2461 Rotate the heating control knob to\u201cOFF\u201d, the indicator light will also be off.<\/p>\n
\u2462 Then switch off the unit and disconnect the power.<\/p>\n
\u2463 Empty the liquid and clean the tank and the unit with a clean cloth for next use.<\/p>\n
\u25a0 Operation Instructions:(Digital models)<\/strong><\/p>\n
\u25c7 Timer setting: When power is connected, the default setting is\u201c05:00\u201d. Press TEME+<\/strong>once will increase time by 1 min; Press TEME+<\/strong>once will decrease time by 1 min. (Free choice and digital countdown control).<\/p>\n
\u25c7 Temperature setting: (heating is optional upon needs): When power is connected, the default setting is \u201c50\u2103\u201d and the Actual is room temp., press TEMP+<\/strong>once, will increase temperature by 1\u2103; Press TEMP-once, will decrease temperature by 1\u2103. If the setting temperature is slower than the actual tank temperature, the operation will stop automatically. When the temperature rises to the setting temperature, the indicating light goes off. When ultrasonic work, two temperature screens show the set temperature and actual temperature that has been reached.<\/p>\n
\u25c7 After setting the time and temperature, press ON\/OFF once, the equipment will work automatically. Press ON\/OFF again, and the work process will stop. Then switch off the unit and disconnect the power supply, empty out the liquid, and clean the tank and the unit with a clean cloth for next use.<\/p>\n
\u25a0 Adjusting power:<\/p>\n
\u25c7 The function is only available for power-adjustable models! Rotate SLOWLY the power knob clockwise to increase the power from 40% to 100%, and counter-clockwise SLOWLY to decrease sonic power.<\/p>\n
Maintenance<\/h2>\n
Maintenance<\/h3>\n
\u25a0 The unit must be opened by an authorized specialized person only for maintenance and care of it.<\/p>\n
\u25a0 Clean the contaminant in the tank frequently.<\/p>\n
Trouble clearing<\/h3>\n
\n\n\n
\n No.<\/td>\n Problems<\/td>\n Possible causes<\/td>\n Solutions<\/td>\n Remarks<\/td>\n<\/tr>\n \n 1<\/td>\n No ultrasonic<\/td>\n A. Loosen or tighten the screw.
\n B. Replace timer or digital panel.C. Inquiry our after-service engineer.<\/td>\nA. Loosen or tighten the screw.
\n B. Replace the timer or digital panel.
\n C. Inquiry our after-service engineer.<\/td>\n<\/td>\n<\/tr>\n \n 2<\/td>\n A. Check the heating plug and connect it well, check the outlet line with the multimeter: if OK and the resistance value is a few hundred OHMs.B. Change the same specification fuse.C. Replace the bad heating pad if the open circuit. D. Check the broken part and change it. E. Inquiry our after-service engineer.<\/td>\n Time control failure<\/td>\n A. Check the heating plug and connect it well, check the outlet line with the multimeter: if OK and the resistance value is a few hundred OHMs.
\n B. Change the same specification fuse.
\n C. Replace the bad heating pad if the open circuit.
\n D. Check the broken part and change it.
\n E. Inquiry our after-service engineer.<\/td>\n<\/td>\n<\/tr>\n \n 3<\/td>\n No heating<\/td>\n A. Heater power switch badlinkage.
\n B. Fuse burnout.
\n C. Heating pad burnout.
\n D. Digital display board out of control.
\n E. Other reasons<\/td>\nA. Check the heating plug and connect it well, check the outlet line with the multimeter: if OK and the resistance value is a few hundred OHMs.
\n B. Change the same specification fuse.
\n C. Replace the bad heating pad if the open circuit.
\n D. Check the broken part and change it.
\n E. Inquiry our after-service engineer.<\/td>\nSuggestion50-60\u2103 <\/td>\n<\/tr>\n \n 4<\/td>\n Temperaturecontrol failure<\/td>\n Temperature control failure<\/td>\n A. Fasten the thermostat header.
\n B. Replace the thermostat.
\n C. Check the broken part and change it.
\n D. Inquiry our after-service engineer.<\/td>\n<\/td>\n<\/tr>\n \n 5<\/td>\n Not well cleaning<\/td>\n A. Connect the ultrasonic button and adjust.
\n B. Adjust the liquid to the best surface.
\n C. Adjust the temperature to the most fitted.
\n D. Stop and switch off the power supply, and replace suitable liquid after the previous liquid cools down.
\n E. Inquiry our after-service engineer.<\/td>\nA. To ensure grounded.
\n B. Check if the machine earth wire loosen.<\/td>\nSuggestion50-60\u2103 <\/td>\n<\/tr>\n \n 6<\/td>\n Electric leakage<\/td>\n A. Customer side not grounded.
\n B. Machine not grounded<\/td>\nA. To ensure grounded.
\n B. Check if the machine earth wire loosens.<\/td>\n<\/td>\n<\/tr>\n \n 7<\/td>\n Other problems<\/td>\n <\/td>\n <\/td>\n <\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/figure>\n FAQs About VEVOR Ultrasonic Cleaner<\/h2>\n
Q1: How do I set up my VEVOR Ultrasonic Cleaner for the first time?<\/h3>\n
A1: Begin by placing your cleaner on a stable, level surface. Fill the tank with water, ensuring it\u2019s within the recommended level. Add the appropriate cleaning solution, set the temperature and timer, and you\u2019re ready to start.<\/p>\n
Q2: What items should I avoid cleaning in the ultrasonic cleaner?<\/h3>\n
A2: Avoid cleaning delicate items like pearls, emeralds, and items with loose settings or cracked surfaces. Always check the item\u2019s compatibility with ultrasonic cleaning before proceeding.<\/p>\n
Q3: How can I troubleshoot common issues with my ultrasonic cleaner?<\/h3>\n
A3: If you encounter issues, ensure the cleaner is properly plugged in and the settings are correctly adjusted. Check for any obstructions in the tank and ensure the cleaning solution is appropriate for the items being cleaned.<\/p>\n
Q4: How often should I change the cleaning solution in my ultrasonic cleaner?<\/h3>\n
A4: Change the solution after every cleaning session or when it becomes visibly dirty. Regular changing of the solution ensures optimal cleaning efficiency.<\/p>\n
Q5: Can I use tap water in my VEVOR Ultrasonic Cleaner?<\/h3>\n
A5: Yes, tap water can be used, but for enhanced cleaning performance, especially for more delicate items, using distilled water is recommended.<\/p>\n
Final Words<\/h2>\n
The VEVOR Ultrasonic Cleaner Instruction Manual is your go-to resource for leveraging the full potential of your ultrasonic cleaner. From setup to maintenance, this guide ensures a seamless and effective cleaning experience. Remember, regular care and correct usage are key to the longevity and efficiency of your VEVOR Ultras<\/a>o<\/a>nic Cleaner<\/a>. Ready to experience the ultimate cleaning solution? Explore our range of VEVOR Ultrasonic Cleaners and elevate your cleaning standards today.<\/p>\n
- Ensure the correct power and switch connection before starting the equipment.<\/li>\n<\/ul>\n