VEVOR Hand Crank Tarp Roller Kit, 64″ to 104″ Wide, Aluminum Alloy Manual

Unlock the full potential of your VEVOR Hand Crank Tarp Roller Kit, 64″ to 104″ Wide, with our comprehensive product manual download. Crafted for aluminum alloy manual cab level dump truck tarp rollers, this manual is an invaluable tool for setup, troubleshooting, and optimization. Whether you’re managing dump trucks, trailers, or trash haulers, our clear and detailed guide ensures you can effortlessly install and maintain your tarp roller system.

The manual covers all aspects of your 7″ sponge-wrapped handle tarp roller kit, providing easy-to-follow step-by-step instructions. Download our user-friendly manual today to ensure peak performance and longevity of your tarp roller.

This manual is a must-have for all VEVOR tarp roller owners. It is perfect for ensuring smooth operations and minimizing downtime. Experience the difference with our expertly crafted guide and keep your equipment running at its best.

DUMP TARP ROLLER KIT MANUAL

MODEL: WBS008

WARNING:

Read and understand this manual before assembling, installing, operating, or servicing this product. Failure to follow these warnings and instructions can cause death, personal injury, or damage to valuable property.

• While assembling and using this product, keep the work area clean and well-lighted, and keep spectators and children out of the work area.
• Wear ANSI-approved safety goggles and heavy-duty work gloves during use.

• Before each use, inspect the general condition of the product. Check for broken, cracked, or bent parts, loose or missing parts, and any situation that may affect its proper operation.
• This product is not a toy. Store it in a safe, dry location out of reach of children and unauthorized people.
• Use as intended only.
• Use common sense when working. Stay alert and concentrate when setting up and using this product. Never operate while under the influence of alcohol, drugs, or medications.
• Dress appropriately. Never wear loose-fitting clothing or jewelry when using. Wear long hair and keep hair, clothing, and gloves away from moving parts.

SAVE THESE INSTRUCTIONS

PRODUCT PARAMETERS

• Primary material: Aluminum alloy
• Telescopic length: 64 to 104 inches.

See the picture below.

PARTS LIST

Hand Crank Tarp Roller Kit Assembly and Installation

• Determine where you would like to place the tarp roller on your dump truck. We recommend mounting the roller outside the dump body’s loading area to prevent damage from loading the dump truck’s body. You’ll also want to place the roller where the winder is easily accessible.
• Now that you have determined where to place the tarproller kit, clamp the bearing bracket (C1/2) assemblies to your desired location. The bearing bracket with the detent lever (C2) should be placed on the driver’s side. Ensure these brackets are aligned on each side vertically. Additionally, mount the brackets high enough to accommodate the entire tarp when it is fully rolled up onto the roll bar.

• To begin installing the brackets (C1/C2), mark the location of the bearing bracket’s mounting holes on each side of the dump truck body. Now, drill 13/32” holes into the four marked locations.
• After drilling the holes, assemble the bearing brackets to the dump body using four 3/8’’x1’’ cap screws, nuts, and lock washers(F) supplied. However, avoid tightening the fasteners at this point; instead, tighten them with your hands to keep them in place.
• Take out the inner hex tube (A) and mark the center of the tube’s length with a pencil. Insert that tube halfway into the driver’s sideroll tube(B1). On the passenger, insert the other side of the roll tube (B2) onto the opposite end of the inner hex tube (A). Now, measure the distance between the inside of the mounted bearing brackets (C1/C2). If the measurement is less than 64”, both roll tube assemblies must be shortened by equal amounts. Separate the two roll tubes to ensure the complete roll tube assembly is 1/4” less than the distance between mounting brackets. Reference your pencil marking to verify the inner hex tube (A) is centered inside the outer roll tube assembly (B1/B2). If it iscentered, screw each roll tube assembly to the inner hex tube using a 1/4”x 1” self drilling and taping screw (F), screw is 2” from the end of the outer tube.

• Slide the entirety of the roll tube (A/B) into the 5-1/2” loop in the tarp (H). Ensure the webbing on the seams of the tarp rests on the bottom of the tarp when installed.
• Ensure the roll tube (A/B) is centered within the tarp (H). Tightly hold the roll tube at the end of the pocket and screw it in place using 1/4” x1” self-drilling tapping screws (F) and fender washers. Space evenly and center across the roll tube. Ensure the screws are at least 2” from the ends of the roll tube. Also, do not screw into the shaft adapters on each end.

• Remove either one of the bearing brackets (C) and slide the tarproll into the remaining bracket. Now that the tarp roll is placed, reposition the bearing bracket and reassemble it to the dump body. Afterward, tighten the 3/8” bracket mounting bolts.
• Center your tarp roll (A/B) between each mounting bracket (C) and tighten set screws into each bearing race.
• Take the sprocket and assemble it onto the 1” shaft on the driver’s side of the roll tube assembly. Ensure the detent lever (D) is in the open position, and slide the sprocket down the shaft until it’s tight against the bearing.
• Now, use the 1/4” x 2” screw and lock nut provided to assemble the crank handle (D) onto the driver’s side of the roll tube shaft (A/B).

• The two small hooks on the straps should be attached to the tarp’s rear corner holes. Now, crimp the large hooks (G) around the tarps (H). The straps are now securely attached to the tarp.
• Take your included pull rope (E) and attach it to the center grommet on the rear of the tarp (H).
• Attach the two rope storage hooks to the dump body. These hooks store the pull rope (E) while the tarp (H) covers the dump body. The hooks must be horizontally mounted and can be bolted or welded to the body. We recommend a distance of 15”-17” between the two hooks.
• On the other side, assemble two more rope storage hooks to the side of the dump body near the crank handle (D). When the tarp is retracted and rolled up, these hooks store the pull rope (E). These hooks must be placed vertically and can be bolted or welded on.

Hand Crank Tarp Roller Kit Maintenance

• Inspect all equipment for loose or worn parts before each use and replace or tighten as needed.
• The tarp should be stored away from fire sources.

 

VEVOR Hand Crank Tarp Roller Kit, 64" to 104" Wide, Aluminum Alloy Manual