VEVOR 1680W MD50 Magnetic Drill 300 RPM Manual

Unlock the full potential of your VEVOR 1680W MD50 Magnetic Drill with our comprehensive product manual. This detailed guide is designed to help you effortlessly set up, optimize, and troubleshoot your electric magnetic drilling system.

With a powerful 1680W motor, 300 RPM spindle speed, and a robust 2900 LBS magnet force, this drill offers exceptional performance for a 2-inch boring diameter. Our manual is user-friendly and meticulously organized, ensuring you have all the information you need at your fingertips.

Whether you are a seasoned professional or a DIY enthusiast, this manual will provide you with step-by-step instructions, safety guidelines, and maintenance tips to maximize your drilling efficiency. Download now and experience the ease of use and enhanced performance of your VEVOR MD50 Magnetic Drill.

VEVOR Magnetic Drill User Manual

Read through carefully and understand these instructions before use.

Magnetic Drill Features and Uses

Magnetic seat drill is a can be adsorbed on iron and steel workpiece surfaces, side, top surface, according to the surface, making a special magnetic seat, production cycle day 18)for drilling electric tools, is
extensively used in the construction, bridge, boiler, shipbuilding and other industries, for large iron and steel workpieces, and in some fieldwork with drilling and flashlight, a magnetic base drill.

It is convenient to use, flexible, can reduce labor intensity, improve machining precision, and work efficiency.

Because it has a unique role in the drilling of large holes(in the 450 largest steel can be drilled 180mm), so it can be used to replace the radial drilling machine.

Matters Needing Attention

1. The magnetic seat drill is provided with a safety protection belt, and it is necessary to fix the magnetic seat in the hanging operation to prevent accidents caused by sudden power failure.
2. When cooling the drill bit, the coolant should be as close to the drill bit. Do not make the coolant splash, especially not the residual liquid in the magnet and the adsorption surface
3. In check, maintenance before, be sure to turn off the switch and unplug the power plug
4. The magnetic seat drill shall be deposited in a dry, clean, and non-corrosive environment in which the child is not to be taken.
5. Maintain a bit sharp, wrench keys should be from the chuck.

Safety Instructions

Warning: when using power tools, to reduce the fire, electric shock, personal injury, and other accidents, one must comply with the following fundamental safety issues

1. Keep the workplace clean. A messy workplace and workstation will lead to an accident.
2. To ensure that the working environment of Botox. Electric tools should not be used in the rain, in damp places, or in flammable and explosive places. The workplace needs to maintain sufficient brightness.
3. Be aware of electric shock accidents. Avoid body contact with objects on the ground.
4. Do not let children close. No idlers in the workplace, but we can not let people touch the tool or the power supply connecting wires.
5. The dress to the right. Do not wear loose-fitting clothing or jewelry, to avoid getting caught in rotating parts. Outdoor work, wear non-slip shoes. Anyone with long hair should wear hats.
6. The use of protective equipment. During the operation, wear goggles and a dust mask.
7. Do not damage the wire. Yanking the wire plug is strictly prohibited. Avoid touching hot, greasy, and sharp metal edges, with the handle clean and dry, as it can become stained with grease.
8. Use a fixed workpiece clamp or vise to clamp the workpiece rather than by hand to ensure work safety.
9. Not to stretch out the work. To maintain stability and balance of the body while on the job.
10. Maintenance tools. Keep the knife sharp, and ensure it is clean for safe operation.
    Specification for lubrication and replacement of spare parts. Regular inspection of the wire, such as for damage, should be commissioned by the professional sector.
11. Extension cables for outdoor use. A special extension cable must be used for outdoor work.
12. Workers should be cautious when working. Should concentrate on the same time.
13. Note: You must use the instructions provided in the spare parts to avoid personal injury and electric shock while operating the magnetic drill.
14. Tools are to be repaired and maintained by full-time personnel. Electric tools are designed and manufactured in accordance with the relevant safety standards. Full-time personnel should use the spare parts that are used in the original production. Otherwise, it will cause harm to the users.
15. Do not push the hard piezoelectric drill. When the operation is blocked, the drill will return to prevent overload of the electric drill. All abnormal decrease cases of speed should be immediately relaxed feed. Drill for some reason, the sudden braking requires immediate cut of the power supply.
16. Work must be put on the cable body back, away from the drill bit.
17. The plug should be in the open position; any extension or cable shall not be removed.
18. Excessive roughness of the adsorption surface has a specific effect on the suction force of the magnetic seat drill, so we should first test to prevent accidents.
19. In the general field, using a magnetic drill, safety protection measures, such as assembly of leakage protector(including leakage protection plug, socket, etc.) Otherwise, the user must wear insulated
    gloves wear insulated shoes, or stand on the insulating mat.
    In wet places or a metal frame upper conductive good workplace, the assembly nominal leakage action current is not greater than 30mA, and the action time is less than 0.

Magnetic Drill Grounding Device

This tool should be properly grounded to prevent the operator from receiving an electric shock. Grounding device should be in accordance with the standard wire and is accompanied by a grounding plug connected with a special line.

The power supply socket is connected to the ground, allowing it to be fixedly connected with the yellow-green wire plug hole and a lug connected to the earth.

Extension cable

Only allow the use of standard extending cable, with a grounding type plug and socket to supply power to the tools. If there is any damage to the cable, it should be repaired or replaced.

Electrical safety

Place the tool in front of the power supply connection. Be sure to note whether the power supply voltage and the voltage marked on the nameplate are the same. If the Power supply voltage is higher than the voltage applied to the tool, it can cause an accident.

If the power supply voltage is lower than the required voltage, there will be a loss in the motor. Therefore, to determine the power voltage, one must not casually plug.

Features and uses

Magnetic seat drill is by a DC electromagnetic sucker adsorption in the steel surface with the drill for rotary cutting processing of portable power tools.

It and the hand-held electric drill are at the level of the iron and steel, top surface, and on-site engineering operations, which can also solve the hand-held electric drill’s high labor intensity and low accuracy. The product conforms to the standard of the safety of the CB38836< hand-held motor and the JB/T9906>
magnetic seat drill.

The magnetic drill can twist drill and drill holes with a hollow drill tool.

Magnetic Drill Technical Data

Install the Magnetic Drill

Note: Be sure to close the switch and pull the plug off before you install or remove the drill bit.

Turn the feed handle, the electric drill rose to the highest position (when necessary, the lateral magnetic drill), mounted on the drill, and remove the same.

For Morse taper shank drill, note flat tin tall alignment sleeve on a waist slot in silver sleeve. Demolition bits will be inclined iron insert sleeve waist groove by a hannering wedge, resulting in the bit off. For the drill chuck, the clamping bit must be a key wrench.

Job Preparation

Buckle the safety belt.

The magnetic seat drill placed at the desired drilling near the site of, and choose the suitable adsorption material and will handle the hole of the security door with a head-worn machine frame, on the other end of the fetter on a sturdy frame, wear closely in and leave about 100mm length head and tighten the buckle bolt. Hand pulled off without loosening or displacement.

The operation steps

1. Insert the power plug. The drill is roughly aligned to the processing position. Then the electromagnet switch is turned on, so that the electromagnet adsorbs on the surface of the iron and steel and other magnetic materials (generally, plate thickness should be greater than 20mm).
2. For a magnetic seat equipped with a rotary table, loosen the handle of the turntable, move the machine frame to drive the machine frame to make the bit towel centered aligned to the working position, and then screw down the handle.
3. The support screw should be adjusted to make it light to the surface of adsorption.
   The open electric switch
4. The grip feed handle is used for slowly drilling operations.

Special note: for a three-phase magnetic base drill, pay attention to the rotation of the electric drill; if when does not meet the requirements, swap the two wires (phase), confirming the direction of rotation of the drill right.

Never a wrong connection of the grounding wire.

Check

The magnetic base drill should undergo regular inspection and maintenance: you
You must check the power cord, inner connection, plug, switch, and insulation resistance. Also, check for any damage to transmission parts.

Lubrication

Magnet drill in the transmission parts(such as gear, rack) is often lubricated and cleaned.

Keep each part and replace the same parts.

When dismantling the magnetic base, the drill should keep each part, which consists of an insulating liner and casing. If there is any damage, you must replace the same components; the assembly should will all parts according to their original position installed, you can not miss.

Quality guarantee period

The company is dedicated to customer service through its internal customer service department.

Possible failures and troubleshooting methods